Warning line in /var/log/asterisk messages file

App_rpt-users
1

I'm seeing the following line occurring:

WARNING[675] acl.c: is not a valid IP

Any suggestions as to where I should look to resolve this?

On a side note, since moving from ACID to DIAL, I am not seeing my Echolink node being active on the echolink.org site.

Have set the system.conf file echolinkenable=1

echolink.conf file seems to be OK.

73,

Dave N

N0KM

···

---
This email has been checked for viruses by Avast antivirus software.
https://www.avast.com/antivirus

2

Dave,
Enable echolink in /etc/asterisk/modules

error is in iax.conf
I dont have a downloaded config handy.

look for a line that has /0.0.0.0

Sorry I can't be more specific.

If you post your iax.conf I can tell you what it is.

73, Steve N4IRS

···

On 11/01/2015 01:54 PM, Dave Newmyer wrote:

I'm seeing the following line occurring:

WARNING[675] acl.c: is not a valid IP

Any suggestions as to where I should look to resolve this?

On a side note, since moving from ACID to DIAL, I am not seeing my Echolink node being active on the echolink.org site.

Have set the system.conf file echolinkenable=1

echolink.conf file seems to be OK.

73,

Dave N

N0KM

---
This email has been checked for viruses by Avast antivirus software.
Download Free Antivirus Software | Avast 2024 PC Protection

_______________________________________________
App_rpt-users mailing list
App_rpt-users@ohnosec.org
http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users

To unsubscribe from this list please visit http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users and scroll down to the bottom of the page. Enter your email address and press the "Unsubscribe or edit options button"
You do not need a password to unsubscribe, you can do it via email confirmation. If you have trouble unsubscribing, please send a message to the list detailing the problem.

--
"Anything is possible if you don't know what you are talking about."
1st Law of Logic

3

permit=/255.255.255.255
change to
; permit=/255.255.255.255

···

On 11/01/2015 02:17 PM, Dave Newmyer wrote:

Thanks Steve:

Here are the screen shots from nano:

  GNU nano 2.2.6 File: iax.conf

; Inter-Asterisk eXchange driver definition
;

[general]
bindport=4569
bindaddr=0.0.0.0
disallow=all
allow=gsm
allow=g726aal2
allow=ulaw
jitterbuffer=yes
forcejitterbuffer=yes
dropcount=2
maxjitterbuffer=4000
maxjitterinterps=10
resyncthreshold=1000
maxexcessbuffer=80
minexcessbuffer=10
jittershrinkrate=1
tos=0x1E
autokill=yes
delayreject=yes
;iaxthreadcount=30
;iaxmaxthreadcount=150

register=28781:261397@register.allstarlink.org

[radio-proxy]
type=user
deny=0.0.0.0/0.0.0.0
permit=/255.255.255.255
context=radio-secure-proxy
disallow=all
allow=g726aal2
transfer=no

[radio-proxy-out]
type=peer
host=
username=28781
secret=261397
auth=md5
disallow=all
allow=g726aal2
transfer=no

; Incoming radio connections

[radio]
type=user
disallow=all
allow=g726aal2
allow=gsm
codecpriority=host
context=radio-secure
transfer=no

; Incoming phone connections to app_rpt

;[radio-control]
;type=user
;secret=nunya
;disallow=all
;allow=gsm
;codecpriority=host
;context=radio-control
;transfer=no

; Setup for outgoing calls

;[yourprovider] ; This needs to change
;type=peer
;host=127.0.0.1
;secret=nunya
;auth=md5
;disallow=all
;allow=gsm
;transfer=no

[allstar-sys]
type=user
context=allstar-sys
auth=rsa
inkeys=allstar
disallow=all
allow=ulaw

[allstar-public]
type=user
context=allstar-public
auth=md5
secret=allstar
disallow=all
allow=ulaw
allow=gsm

#includeifexists custom/iax.conf

                                           [ Read 100 lines ]
^G Get Help ^O WriteOut ^R Read File ^Y Prev Page ^K Cut Text ^C Cur Pos
^X Exit ^J Justify ^W Where Is ^V Next Page ^U UnCut Text ^T To Spell

On 11/1/2015 12:01 PM, Steve Zingman wrote:

Dave,
Enable echolink in /etc/asterisk/modules

error is in iax.conf
I dont have a downloaded config handy.

look for a line that has /0.0.0.0

Sorry I can't be more specific.

If you post your iax.conf I can tell you what it is.

73, Steve N4IRS

On 11/01/2015 01:54 PM, Dave Newmyer wrote:

I'm seeing the following line occurring:

WARNING[675] acl.c: is not a valid IP

Any suggestions as to where I should look to resolve this?

On a side note, since moving from ACID to DIAL, I am not seeing my Echolink node being active on the echolink.org site.

Have set the system.conf file echolinkenable=1

echolink.conf file seems to be OK.

73,

Dave N

N0KM

---
This email has been checked for viruses by Avast antivirus software.
Download Free Antivirus Software | Avast 2024 PC Protection

_______________________________________________
App_rpt-users mailing list
App_rpt-users@ohnosec.org
http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users

To unsubscribe from this list please visit http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users and scroll down to the bottom of the page. Enter your email address and press the "Unsubscribe or edit options button"
You do not need a password to unsubscribe, you can do it via email confirmation. If you have trouble unsubscribing, please send a message to the list detailing the problem.

---
This email has been checked for viruses by Avast antivirus software.
Download Free Antivirus Software | Avast 2024 PC Protection

--
"Anything is possible if you don't know what you are talking about."
1st Law of Logic