# Trouble with RTCM and Garmin GPS (18x LVC)

**URL:** <https://community.allstarlink.org/t/trouble-with-rtcm-and-garmin-gps-18x-lvc/13569>\
**Category:** AllStarLink\
**Created:** [November 16, 2017, 8:39am UTC](https://community.allstarlink.org/t/trouble-with-rtcm-and-garmin-gps-18x-lvc/13569 "2017-11-16T08:39:36Z")\
**Posts on this page:** 7\
**Page:** 1

<div class="post-metadata">

**Author:** ![Dpk](https://community.allstarlink.org/user_avatar/community.allstarlink.org/dpk/32/810_2.png) [@Dpk](https://community.allstarlink.org/u/Dpk)\
**Post date:** [November 16, 2017, 8:39am UTC](https://community.allstarlink.org/t/trouble-with-rtcm-and-garmin-gps-18x-lvc/13569/1 "2017-11-16T08:39:36Z")

</div>

I can’t get the RTCM to recognize the attached GPS unit.  
Reference: [http://static.garmincdn.com/pumac/GPS\_18x\_Tech\_Specs.pdf](http://static.garmincdn.com/pumac/GPS_18x_Tech_Specs.pdf)

I have determined that pin6 on the DB15 of the RTCM is transmit data to the GPS (using an oscilloscope) and that’s hooked to the RxData line of the Garmin (green). Will the Garmin respond if it does not have lock?

RTCM diagnostics complain:

Running Diagnostics…

Warning!! VF Diode NOT calibrated!!!

Testing PTT/External CTCSS

Error - Failed to read PTT/CTCSS in asserted state

Testing GPS UART

Error - Failed to read data from GPS UART

Any hints? or ways to get more diagnostics?

-Doug-

---

<div class="post-metadata">

**Author:** ![Chuck\_Henderson](https://community.allstarlink.org/letter_avatar_proxy/v4/letter/c/ba9def/32.png) [@Chuck\_Henderson](https://community.allstarlink.org/u/Chuck_Henderson)\
**Post date:** [November 16, 2017, 10:42am UTC](https://community.allstarlink.org/t/trouble-with-rtcm-and-garmin-gps-18x-lvc/13569/2 "2017-11-16T10:42:20Z")

</div>

For the Garmin GPS18x LVC, 5m to the RTCM, the following works for me:

I have green on 6, yellow on 7, shield and 1-small black and large black on 8, white on 14, red on 13, 1-small black n/c.  
You need to do the diode calibration procedure and then set the levels.

Hope this helps.

Chuck

> **···**
>
> On Thu, Nov 16, 2017 at 2:39 AM, Doug Kingston [dpk@randomnotes.org](mailto:dpk@randomnotes.org) wrote:
> 
> > I can’t get the RTCM to recognize the attached GPS unit.  
> > Reference: [http://static.garmincdn.com/pumac/GPS\_18x\_Tech\_Specs.pdf](http://static.garmincdn.com/pumac/GPS_18x_Tech_Specs.pdf)
> 
> > 
> 
> > I have determined that pin6 on the DB15 of the RTCM is transmit data to the GPS (using an oscilloscope) and that’s hooked to the RxData line of the Garmin (green). Will the Garmin respond if it does not have lock?
> 
> > 
> 
> > RTCM diagnostics complain:
> 
> > Running Diagnostics…
> 
> > 
> 
> > Warning!! VF Diode NOT calibrated!!!
> 
> > 
> 
> > Testing PTT/External CTCSS
> 
> > Error - Failed to read PTT/CTCSS in asserted state
> 
> > Testing GPS UART
> 
> > Error - Failed to read data from GPS UART
> 
> > 
> 
> > Any hints? or ways to get more diagnostics?
> 
> > 
> 
> > -Doug-
> 
> >

---

<div class="post-metadata">

**Author:** ![Dpk](https://community.allstarlink.org/user_avatar/community.allstarlink.org/dpk/32/810_2.png) [@Dpk](https://community.allstarlink.org/u/Dpk)\
**Post date:** [November 16, 2017, 3:51pm UTC](https://community.allstarlink.org/t/trouble-with-rtcm-and-garmin-gps-18x-lvc/13569/3 "2017-11-16T15:51:02Z")

</div>

Did you need to do the calibration before the GPS would show functioning? I have not tackled the RF side yet.

-Doug-

> **···**
>
> On Thu, Nov 16, 2017 at 2:42 AM, Chuck Henderson [rpt2@chuck.midlandsnetworking.com](mailto:rpt2@chuck.midlandsnetworking.com) wrote:
> 
> > For the Garmin GPS18x LVC, 5m to the RTCM, the following works for me:
> 
> > I have green on 6, yellow on 7, shield and 1-small black and large black on 8, white on 14, red on 13, 1-small black n/c.  
> > You need to do the diode calibration procedure and then set the levels.
> 
> > Hope this helps.
> 
> > Chuck
> 
> > * * *
> > 
> > App\_rpt-users mailing list
> > 
> > [App\_rpt-users@lists.allstarlink.org](mailto:App_rpt-users@lists.allstarlink.org)
> > 
> > [http://lists.allstarlink.org/cgi-bin/mailman/listinfo/app\_rpt-users](http://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users)
> > 
> > To unsubscribe from this list please visit [http://lists.allstarlink.org/cgi-bin/mailman/listinfo/app\_rpt-users](http://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users) and scroll down to the bottom of the page. Enter your email address and press the “Unsubscribe or edit options button”
> > 
> > You do not need a password to unsubscribe, you can do it via email confirmation. If you have trouble unsubscribing, please send a message to the list detailing the problem.
> 
> On Thu, Nov 16, 2017 at 2:39 AM, Doug Kingston [dpk@randomnotes.org](mailto:dpk@randomnotes.org) wrote:
> 
> > I can’t get the RTCM to recognize the attached GPS unit.  
> > Reference: [http://static.garmincdn.com/pumac/GPS\_18x\_Tech\_Specs.pdf](http://static.garmincdn.com/pumac/GPS_18x_Tech_Specs.pdf)
> 
> > 
> 
> > I have determined that pin6 on the DB15 of the RTCM is transmit data to the GPS (using an oscilloscope) and that’s hooked to the RxData line of the Garmin (green). Will the Garmin respond if it does not have lock?
> 
> > 
> 
> > RTCM diagnostics complain:
> 
> > Running Diagnostics…
> 
> > 
> 
> > Warning!! VF Diode NOT calibrated!!!
> 
> > 
> 
> > Testing PTT/External CTCSS
> 
> > Error - Failed to read PTT/CTCSS in asserted state
> 
> > Testing GPS UART
> 
> > Error - Failed to read data from GPS UART
> 
> > 
> 
> > Any hints? or ways to get more diagnostics?
> 
> > 
> 
> > -Doug-
> 
> >

---

<div class="post-metadata">

**Author:** ![VE7FET](https://community.allstarlink.org/user_avatar/community.allstarlink.org/ve7fet/32/1267_2.png) [@VE7FET](https://community.allstarlink.org/u/VE7FET)\
**Post date:** [November 16, 2017, 3:58pm UTC](https://community.allstarlink.org/t/trouble-with-rtcm-and-garmin-gps-18x-lvc/13569/4 "2017-11-16T15:58:48Z")

</div>

Have you looked at:

[http://wiki.allstarlink.org/wiki/RTCM\_Client#GPS](http://wiki.allstarlink.org/wiki/RTCM_Client#GPS)

Specifically, does this Garmin use 5V or 3.3V logic?

I believe the RTCM uses 5V logic only (the VOTER) will do either.

If your Garmin is 3.3V, it may have issues.

Also, make sure the baud rate is correct, and it is configured to send the required NMEA sentences.

Lee

> **···**
>
> On Nov 16, 2017 12:40 AM, “Doug Kingston” [dpk@randomnotes.org](mailto:dpk@randomnotes.org) wrote:
> 
> > I can’t get the RTCM to recognize the attached GPS unit.  
> > Reference: [http://static.garmincdn.com/pumac/GPS\_18x\_Tech\_Specs.pdf](http://static.garmincdn.com/pumac/GPS_18x_Tech_Specs.pdf)
> 
> > 
> 
> > I have determined that pin6 on the DB15 of the RTCM is transmit data to the GPS (using an oscilloscope) and that’s hooked to the RxData line of the Garmin (green). Will the Garmin respond if it does not have lock?
> 
> > 
> 
> > RTCM diagnostics complain:
> 
> > Running Diagnostics…
> 
> > 
> 
> > Warning!! VF Diode NOT calibrated!!!
> 
> > 
> 
> > Testing PTT/External CTCSS
> 
> > Error - Failed to read PTT/CTCSS in asserted state
> 
> > Testing GPS UART
> 
> > Error - Failed to read data from GPS UART
> 
> > 
> 
> > Any hints? or ways to get more diagnostics?
> 
> > 
> 
> > -Doug-
> 
> > * * *
> > 
> > App\_rpt-users mailing list
> > 
> > [App\_rpt-users@lists.allstarlink.org](mailto:App_rpt-users@lists.allstarlink.org)
> > 
> > [http://lists.allstarlink.org/cgi-bin/mailman/listinfo/app\_rpt-users](http://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users)
> > 
> > To unsubscribe from this list please visit [http://lists.allstarlink.org/cgi-bin/mailman/listinfo/app\_rpt-users](http://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users) and scroll down to the bottom of the page. Enter your email address and press the “Unsubscribe or edit options button”
> > 
> > You do not need a password to unsubscribe, you can do it via email confirmation. If you have trouble unsubscribing, please send a message to the list detailing the problem.

---

<div class="post-metadata">

**Author:** ![Dpk](https://community.allstarlink.org/user_avatar/community.allstarlink.org/dpk/32/810_2.png) [@Dpk](https://community.allstarlink.org/u/Dpk)\
**Post date:** [November 16, 2017, 6:09pm UTC](https://community.allstarlink.org/t/trouble-with-rtcm-and-garmin-gps-18x-lvc/13569/5 "2017-11-16T18:09:08Z")

</div>

Thanks for the pointer to the GPS writeup. I had missed this. Will review and see where I get.

> **···**
>
> On Thu, Nov 16, 2017 at 7:58 AM, Lee Woldanski [ve7fet@tparc.org](mailto:ve7fet@tparc.org) wrote:
> 
> > Have you looked at:
> 
> > [http://wiki.allstarlink.org/wiki/RTCM\_Client#GPS](http://wiki.allstarlink.org/wiki/RTCM_Client#GPS)
> 
> > 
> 
> > Specifically, does this Garmin use 5V or 3.3V logic?
> 
> > 
> 
> > I believe the RTCM uses 5V logic only (the VOTER) will do either.
> 
> > 
> 
> > If your Garmin is 3.3V, it may have issues.
> 
> > 
> 
> > Also, make sure the baud rate is correct, and it is configured to send the required NMEA sentences.
> 
> > 
> 
> > 
> 
> > Lee
> 
> > * * *
> > 
> > App\_rpt-users mailing list
> > 
> > [App\_rpt-users@lists.allstarlink.org](mailto:App_rpt-users@lists.allstarlink.org)
> > 
> > [http://lists.allstarlink.org/cgi-bin/mailman/listinfo/app\_rpt-users](http://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users)
> > 
> > To unsubscribe from this list please visit [http://lists.allstarlink.org/cgi-bin/mailman/listinfo/app\_rpt-users](http://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users) and scroll down to the bottom of the page. Enter your email address and press the “Unsubscribe or edit options button”
> > 
> > You do not need a password to unsubscribe, you can do it via email confirmation. If you have trouble unsubscribing, please send a message to the list detailing the problem.
> 
> On Nov 16, 2017 12:40 AM, “Doug Kingston” [dpk@randomnotes.org](mailto:dpk@randomnotes.org) wrote:
> 
> > I can’t get the RTCM to recognize the attached GPS unit.  
> > Reference: [http://static.garmincdn.com/pumac/GPS\_18x\_Tech\_Specs.pdf](http://static.garmincdn.com/pumac/GPS_18x_Tech_Specs.pdf)
> 
> > 
> 
> > I have determined that pin6 on the DB15 of the RTCM is transmit data to the GPS (using an oscilloscope) and that’s hooked to the RxData line of the Garmin (green). Will the Garmin respond if it does not have lock?
> 
> > 
> 
> > RTCM diagnostics complain:
> 
> > Running Diagnostics…
> 
> > 
> 
> > Warning!! VF Diode NOT calibrated!!!
> 
> > 
> 
> > Testing PTT/External CTCSS
> 
> > Error - Failed to read PTT/CTCSS in asserted state
> 
> > Testing GPS UART
> 
> > Error - Failed to read data from GPS UART
> 
> > 
> 
> > Any hints? or ways to get more diagnostics?
> 
> > 
> 
> > -Doug-
> 
> > 
> 
> > * * *
> > 
> > App\_rpt-users mailing list
> > 
> > [App\_rpt-users@lists.allstarlink.org](mailto:App_rpt-users@lists.allstarlink.org)
> > 
> > [http://lists.allstarlink.org/cgi-bin/mailman/listinfo/app\_rpt-users](http://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users)
> > 
> > To unsubscribe from this list please visit [http://lists.allstarlink.org/cgi-bin/mailman/listinfo/app\_rpt-users](http://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users) and scroll down to the bottom of the page. Enter your email address and press the “Unsubscribe or edit options button”
> > 
> > You do not need a password to unsubscribe, you can do it via email confirmation. If you have trouble unsubscribing, please send a message to the list detailing the problem.

---

<div class="post-metadata">

**Author:** ![Chuck\_Henderson](https://community.allstarlink.org/letter_avatar_proxy/v4/letter/c/ba9def/32.png) [@Chuck\_Henderson](https://community.allstarlink.org/u/Chuck_Henderson)\
**Post date:** [November 17, 2017, 2:44am UTC](https://community.allstarlink.org/t/trouble-with-rtcm-and-garmin-gps-18x-lvc/13569/6 "2017-11-17T02:44:46Z")

</div>

I only use this Garmin (GPS18x LVC, 5m) and have no problem with the RTCM. I got most of them many years ago but the last one I bought in 2016 and it worked fine also. I just hook them up and they work. I have not looked at the pulse with a scope. I recall there is a JP4 that can be changed in the RTCM. In one position, (1-2), it has thresholds of less than 0.8v and greater than 2.0V and is ±25v tolerant and in the other default position (2-3) it should be standard TTL input and 0 to 5 volt tolerant.  
Chuck

> **···**
>
> On Thu, Nov 16, 2017 at 9:58 AM, Lee Woldanski [ve7fet@tparc.org](mailto:ve7fet@tparc.org) wrote:
> 
> > Have you looked at:
> 
> > [http://wiki.allstarlink.org/wiki/RTCM\_Client#GPS](http://wiki.allstarlink.org/wiki/RTCM_Client#GPS)
> 
> > 
> 
> > Specifically, does this Garmin use 5V or 3.3V logic?
> 
> > 
> 
> > I believe the RTCM uses 5V logic only (the VOTER) will do either.
> 
> > 
> 
> > If your Garmin is 3.3V, it may have issues.
> 
> > 
> 
> > Also, make sure the baud rate is correct, and it is configured to send the required NMEA sentences.
> 
> > 
> 
> > 
> 
> > Lee
> 
> > 
> 
> On Nov 16, 2017 12:40 AM, “Doug Kingston” [dpk@randomnotes.org](mailto:dpk@randomnotes.org) wrote:
> 
> > I can’t get the RTCM to recognize the attached GPS unit.  
> > Reference: [http://static.garmincdn.com/pumac/GPS\_18x\_Tech\_Specs.pdf](http://static.garmincdn.com/pumac/GPS_18x_Tech_Specs.pdf)
> 
> > 
> 
> > I have determined that pin6 on the DB15 of the RTCM is transmit data to the GPS (using an oscilloscope) and that’s hooked to the RxData line of the Garmin (green). Will the Garmin respond if it does not have lock?
> 
> > 
> 
> > RTCM diagnostics complain:
> 
> > Running Diagnostics…
> 
> > 
> 
> > Warning!! VF Diode NOT calibrated!!!
> 
> > 
> 
> > Testing PTT/External CTCSS
> 
> > Error - Failed to read PTT/CTCSS in asserted state
> 
> > Testing GPS UART
> 
> > Error - Failed to read data from GPS UART
> 
> > 
> 
> > Any hints? or ways to get more diagnostics?
> 
> > 
> 
> > -Doug-

---

<div class="post-metadata">

**Author:** ![Dpk](https://community.allstarlink.org/user_avatar/community.allstarlink.org/dpk/32/810_2.png) [@Dpk](https://community.allstarlink.org/u/Dpk)\
**Post date:** [November 17, 2017, 4:58am UTC](https://community.allstarlink.org/t/trouble-with-rtcm-and-garmin-gps-18x-lvc/13569/7 "2017-11-17T04:58:48Z")

</div>

Thanks to the advice above, my problems are resolved. Thanks all!

-Doug-

> **···**
>
> On Thu, Nov 16, 2017 at 6:44 PM, Chuck Henderson [rpt2@chuck.midlandsnetworking.com](mailto:rpt2@chuck.midlandsnetworking.com) wrote:
> 
> > Chuck
> 
> > I only use this Garmin (GPS18x LVC, 5m) and have no problem with the RTCM. I got most of them many years ago but the last one I bought in 2016 and it worked fine also. I just hook them up and they work. I have not looked at the pulse with a scope. I recall there is a JP4 that can be changed in the RTCM. In one position, (1-2), it has thresholds of less than 0.8v and greater than 2.0V and is ±25v tolerant and in the other default position (2-3) it should be standard TTL input and 0 to 5 volt tolerant.
> 
> > * * *
> > 
> > App\_rpt-users mailing list
> > 
> > [App\_rpt-users@lists.allstarlink.org](mailto:App_rpt-users@lists.allstarlink.org)
> > 
> > [http://lists.allstarlink.org/cgi-bin/mailman/listinfo/app\_rpt-users](http://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users)
> > 
> > To unsubscribe from this list please visit [http://lists.allstarlink.org/cgi-bin/mailman/listinfo/app\_rpt-users](http://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users) and scroll down to the bottom of the page. Enter your email address and press the “Unsubscribe or edit options button”
> > 
> > You do not need a password to unsubscribe, you can do it via email confirmation. If you have trouble unsubscribing, please send a message to the list detailing the problem.
> 
> On Thu, Nov 16, 2017 at 9:58 AM, Lee Woldanski [ve7fet@tparc.org](mailto:ve7fet@tparc.org) wrote:
> 
> > Have you looked at:
> 
> > [http://wiki.allstarlink.org/wiki/RTCM\_Client#GPS](http://wiki.allstarlink.org/wiki/RTCM_Client#GPS)
> 
> > 
> 
> > Specifically, does this Garmin use 5V or 3.3V logic?
> 
> > 
> 
> > I believe the RTCM uses 5V logic only (the VOTER) will do either.
> 
> > 
> 
> > If your Garmin is 3.3V, it may have issues.
> 
> > 
> 
> > Also, make sure the baud rate is correct, and it is configured to send the required NMEA sentences.
> 
> > 
> 
> > 
> 
> > Lee
> 
> > 
> 
> On Nov 16, 2017 12:40 AM, “Doug Kingston” [dpk@randomnotes.org](mailto:dpk@randomnotes.org) wrote:
> 
> > I can’t get the RTCM to recognize the attached GPS unit.  
> > Reference: [http://static.garmincdn.com/pumac/GPS\_18x\_Tech\_Specs.pdf](http://static.garmincdn.com/pumac/GPS_18x_Tech_Specs.pdf)
> 
> > 
> 
> > I have determined that pin6 on the DB15 of the RTCM is transmit data to the GPS (using an oscilloscope) and that’s hooked to the RxData line of the Garmin (green). Will the Garmin respond if it does not have lock?
> 
> > 
> 
> > RTCM diagnostics complain:
> 
> > Running Diagnostics…
> 
> > 
> 
> > Warning!! VF Diode NOT calibrated!!!
> 
> > 
> 
> > Testing PTT/External CTCSS
> 
> > Error - Failed to read PTT/CTCSS in asserted state
> 
> > Testing GPS UART
> 
> > Error - Failed to read data from GPS UART
> 
> > 
> 
> > Any hints? or ways to get more diagnostics?
> 
> > 
> 
> > -Doug-
