# Only able to make a connect from one to the other between 2 private nodes?

**URL:** <https://community.allstarlink.org/t/only-able-to-make-a-connect-from-one-to-the-other-between-2-private-nodes/18853>\
**Category:** AllStarLink\
**Created:** [September 6, 2021, 3:21pm UTC](https://community.allstarlink.org/t/only-able-to-make-a-connect-from-one-to-the-other-between-2-private-nodes/18853 "2021-09-06T15:21:20Z")\
**Posts on this page:** 14\
**Page:** 1

<div class="post-metadata">

**Author:** ![AH6LE](https://community.allstarlink.org/user_avatar/community.allstarlink.org/ah6le/32/1817_2.png) [@AH6LE](https://community.allstarlink.org/u/AH6LE)\
**Post date:** [September 6, 2021, 3:21pm UTC](https://community.allstarlink.org/t/only-able-to-make-a-connect-from-one-to-the-other-between-2-private-nodes/18853/1 "2021-09-06T15:21:20Z")

</div>

Search didn’t point me in the right direction so here I am…

I have multiple private nodes, all on the same subnet and vlan. I run one as a hub and the other 3 are connected to by the hub on startup (permanently). Well, all except one. Hub is node 1100 and other node in question is 1102

1100 cannot establish a connection to 1102 (Supermon reports “Connecting” in red and it never connects). However, if I connect FROM 1102 to 1100, connect is pretty much immediate.

[nodes] looks correct in both nodes and I am stumped!

---

<div class="post-metadata">

**Author:** ![Bob\_Pyke](https://community.allstarlink.org/user_avatar/community.allstarlink.org/bob_pyke/32/1396_2.png) [@Bob\_Pyke](https://community.allstarlink.org/u/Bob_Pyke)\
**Post date:** [September 6, 2021, 6:04pm UTC](https://community.allstarlink.org/t/only-able-to-make-a-connect-from-one-to-the-other-between-2-private-nodes/18853/2 "2021-09-06T18:04:46Z")

</div>

Sounds like a typo somewhere, or your NAT setup has an issue.

---

<div class="post-metadata">

**Author:** ![AH6LE](https://community.allstarlink.org/user_avatar/community.allstarlink.org/ah6le/32/1817_2.png) [@AH6LE](https://community.allstarlink.org/u/AH6LE)\
**Post date:** [September 6, 2021, 6:30pm UTC](https://community.allstarlink.org/t/only-able-to-make-a-connect-from-one-to-the-other-between-2-private-nodes/18853/3 "2021-09-06T18:30:04Z")

</div>

Have had another look at the conf files and no typos found

As for NAT, unnecessary. As I said, same subnet, same vlan (as well as with another node on the same vlan and subnet, there is no problem connecting to it)

---

<div class="post-metadata">

**Author:** ![AH6LE](https://community.allstarlink.org/user_avatar/community.allstarlink.org/ah6le/32/1817_2.png) [@AH6LE](https://community.allstarlink.org/u/AH6LE)\
**Post date:** [September 6, 2021, 6:35pm UTC](https://community.allstarlink.org/t/only-able-to-make-a-connect-from-one-to-the-other-between-2-private-nodes/18853/4 "2021-09-06T18:35:07Z")

</div>

From Node 1100 rpt.conf, [nodes] stanza

1100 = [radio@127.0.0.1](mailto:radio@127.0.0.1)/1100,NONE ; Local node  
1101 = [radio@10.48.13.20](mailto:radio@10.48.13.20)/1101,NONE ; Remote node - 442.675 - AH6LEUHF  
1102 = [radio@10.150.180.37](mailto:radio@10.150.180.37)/1102,NONE ; Remote node - 441.875 AH6LEUHF2  
1103 = [radio@10.150.180.36](mailto:radio@10.150.180.36)/1103,NONE ; Remote node - 146.920 AH6LEVHF

From Node 1102 rpt.conf, [nodes] stanza

1102 = [radio@127.0.0.1](mailto:radio@127.0.0.1)/1102,NONE ; Local node 441.875 AH6LEUHF2   
1100 = [radio@10.150.180.35](mailto:radio@10.150.180.35)/1100,NONE ; Remote node - Hub no RF  
1101 = [radio@10.48.13.20](mailto:radio@10.48.13.20)/1101,NONE ; Remote node - 442.675 - AH6LEUHF  
1103 = [radio@10.150.180.36](mailto:radio@10.150.180.36)/1103,NONE ; mote node - 146.920 AH6LEVHF

---

<div class="post-metadata">

**Author:** ![N4IRS](https://community.allstarlink.org/user_avatar/community.allstarlink.org/n4irs/32/548_2.png) [@N4IRS](https://community.allstarlink.org/u/N4IRS)\
**Post date:** [September 6, 2021, 7:15pm UTC](https://community.allstarlink.org/t/only-able-to-make-a-connect-from-one-to-the-other-between-2-private-nodes/18853/5 "2021-09-06T19:15:46Z")

</div>

Are you watching the asterisk consoles on 1100 and 1102 while connecting? Increase verbosity and debug to see connection attempts. Watch connection from 1102 to see what success looks like.

---

<div class="post-metadata">

**Author:** ![Mike](https://community.allstarlink.org/user_avatar/community.allstarlink.org/mike/32/1569_2.png) [@Mike](https://community.allstarlink.org/u/Mike)\
**Post date:** [September 6, 2021, 7:23pm UTC](https://community.allstarlink.org/t/only-able-to-make-a-connect-from-one-to-the-other-between-2-private-nodes/18853/6 "2021-09-06T19:23:44Z")

</div>

Since you are using 2 computers behind the same nat, and I’m sure you are not using the same iax port…

You need to specify the port in your ‘nodes’  
1100 = radio@10.150.180.35:4570/1100,NONE ; Remote node - Hub no RF

If not the local machine (127.0.0.1) specify the iax port used

---

<div class="post-metadata">

**Author:** ![N4IRS](https://community.allstarlink.org/user_avatar/community.allstarlink.org/n4irs/32/548_2.png) [@N4IRS](https://community.allstarlink.org/u/N4IRS)\
**Post date:** [September 6, 2021, 7:45pm UTC](https://community.allstarlink.org/t/only-able-to-make-a-connect-from-one-to-the-other-between-2-private-nodes/18853/7 "2021-09-06T19:45:35Z")

</div>

I don’t see where NAT comes into play here. Both systems on the same subnet.

---

<div class="post-metadata">

**Author:** ![N5ZR](https://community.allstarlink.org/user_avatar/community.allstarlink.org/n5zr/32/1816_2.png) [@N5ZR](https://community.allstarlink.org/u/N5ZR)\
**Post date:** [September 6, 2021, 8:03pm UTC](https://community.allstarlink.org/t/only-able-to-make-a-connect-from-one-to-the-other-between-2-private-nodes/18853/8 "2021-09-06T20:03:47Z")

</div>

Could this be a radio-secure permission in the extensions.conf on that node?

---

<div class="post-metadata">

**Author:** ![AH6LE](https://community.allstarlink.org/user_avatar/community.allstarlink.org/ah6le/32/1817_2.png) [@AH6LE](https://community.allstarlink.org/u/AH6LE)\
**Post date:** [September 6, 2021, 10:47pm UTC](https://community.allstarlink.org/t/only-able-to-make-a-connect-from-one-to-the-other-between-2-private-nodes/18853/9 "2021-09-06T22:47:55Z")

</div>

As I said, I have another node on the same VLAN and subnet and I’m only having issues with connecting from 1100 \> 1102.

1100 connects to 1101 (a remotely located one on the AREDN Mesh) and 1103 (on the same VLAN and subnet) without problems. I don’t see any difference in extensions.conf (aside from node # of course) between them

---

<div class="post-metadata">

**Author:** ![AH6LE](https://community.allstarlink.org/user_avatar/community.allstarlink.org/ah6le/32/1817_2.png) [@AH6LE](https://community.allstarlink.org/u/AH6LE)\
**Post date:** [September 6, 2021, 10:48pm UTC](https://community.allstarlink.org/t/only-able-to-make-a-connect-from-one-to-the-other-between-2-private-nodes/18853/10 "2021-09-06T22:48:47Z")

</div>

Good idea, I will give that a try

---

<div class="post-metadata">

**Author:** ![Mike](https://community.allstarlink.org/user_avatar/community.allstarlink.org/mike/32/1569_2.png) [@Mike](https://community.allstarlink.org/u/Mike)\
**Post date:** [September 7, 2021, 12:09am UTC](https://community.allstarlink.org/t/only-able-to-make-a-connect-from-one-to-the-other-between-2-private-nodes/18853/11 "2021-09-07T00:09:40Z")

</div>

If you do not specify the iax port of the remote private node… how does it know ?  
Behind the same NAT, they are obviously not the same port number or you could not port forward to the correct machine… or perhaps that too is a issue if the same port, but you must specify it in the nodes segment as ‘connection info’ .

---

<div class="post-metadata">

**Author:** ![AH6LE](https://community.allstarlink.org/user_avatar/community.allstarlink.org/ah6le/32/1817_2.png) [@AH6LE](https://community.allstarlink.org/u/AH6LE)\
**Post date:** [September 7, 2021, 12:11am UTC](https://community.allstarlink.org/t/only-able-to-make-a-connect-from-one-to-the-other-between-2-private-nodes/18853/12 "2021-09-07T00:11:53Z")

</div>

Found the problem.

Maybe this belongs in the allmon part of the forum but as it turns out, Supermon for ASL doesn’t actually reload the Iax2, Rpt, & Dialplan files as the “Iax2, Rpt, & Dialplan Reload” button claims.

In my case,Asterisk was working with an old rpt.conf file with the wrong IP for node 1102 despite the above. Using the Asterisk CLI revealed that. Thanks to N4IRS for suggesting that

---

<div class="post-metadata">

**Author:** ![N4IRS](https://community.allstarlink.org/user_avatar/community.allstarlink.org/n4irs/32/548_2.png) [@N4IRS](https://community.allstarlink.org/u/N4IRS)\
**Post date:** [September 7, 2021, 12:23am UTC](https://community.allstarlink.org/t/only-able-to-make-a-connect-from-one-to-the-other-between-2-private-nodes/18853/13 "2021-09-07T00:23:14Z")

</div>

The connection is not being NATed since it’s on the same subnet. The 2 nodes could be on the same IAX port.That being said, I always add the port number to the entry in the nodes section even if it’s the default 4569. It leaves no room for doubt.

---

<div class="post-metadata">

**Author:** ![system](https://community.allstarlink.org/uploads/default/original/2X/4/42700284e201b031bd667c3f63bbae05a74b3104.png) [@system](https://community.allstarlink.org/u/system)\
**Post date:** [September 10, 2021, 12:23am UTC](https://community.allstarlink.org/t/only-able-to-make-a-connect-from-one-to-the-other-between-2-private-nodes/18853/14 "2021-09-10T00:23:20Z")

</div>

Closed on September 10, 2021, 12:23am UTC

This topic was automatically closed 3 days after the last reply. New replies are no longer allowed.
