My link is up and running but i can see my node and echolink node is showing up but when i key up nothing happening no audio no etc this was old echolink set up now convert to allstar my statistic show only 1 keyed from rebooting the pi port forward and dmz the pi in my router still stump any clues?
(By ‘key up the radio’ I assume you mean some radio other than the one that is connected to your node, but transmitting on the input frequency of the node radio - and that you have done the USB fob setup).
log into the asterisk CLI and set verbose to 5
CLI> core set verbose 5
Then key your radio and see if the node receiver is working properly
you should see
RPT_RXKEYED=1
RPT_TXKEYED=0
RPT_ETXKEYED=0
RPT_NUMLINKS=1
(and more stuff)
and then
RPT_TXKEYED=1
RPT_RXKEYED=1
RPT_ETXKEYED=0
RPT_NUMLINKS=1
(more stuff)
RPT_ETXKEYED=1
RPT_TXKEYED=1
RPT_RXKEYED=1
RPT_NUMLINKS=1
if not, you could have the wrong sense for COS or wrong CTCSS or various other problems.
Ken
···
From: Ke2n via AllStarLink Discussion Groups noreply@community.allstarlink.org
Sent: Tuesday, September 29, 2020 9:05 PM
To: ancer13@hotmail.com ancer13@hotmail.com
Subject: [AllStarLink Discussion Groups] Link is up but some issue
 |
Ke2n September 30 |
|---|
(By ‘key up the radio’ I assume you mean some radio other than the one that is connected to your node, but transmitting on the input frequency of the node radio - and that you have done the USB fob setup).
log into the asterisk CLI and set verbose to 5
CLI> core set verbose 5
Then key your radio and see if the node receiver is working properly
you should see
RPT_RXKEYED=1
RPT_TXKEYED=0
RPT_ETXKEYED=0
RPT_NUMLINKS=1
(and more stuff)
and then
RPT_TXKEYED=1
RPT_RXKEYED=1
RPT_ETXKEYED=0
RPT_NUMLINKS=1
(more stuff)
RPT_ETXKEYED=1
RPT_TXKEYED=1
RPT_RXKEYED=1
RPT_NUMLINKS=1
if not, you could have the wrong sense for COS or wrong CTCSS or various other problems.
Ken
Visit Topic or reply to this email to respond.
To unsubscribe from these emails, click here.
What you screen snapped appears to be the last two sets of node variables - the ones you get when you unkey. The others probably scrolled off the top of the screen. If you were to SSH connect with a PC running puTTY (for example) you could capture everything.
In any case - if in fact that is showing the last two - it indicates the problem. RX is keyed when it should be unkeyed - so your COS is backwards (active high/low reversed).
Here is what the last two look like - when I un-key my node
Node Variable dump for node 27021:
RPT_ETXKEYED=0
RPT_RXKEYED=0
RPT_TXKEYED=1
RPT_NUMLINKS=1
RPT_LINKS=1,T1708
RPT_NUMALINKS=1
RPT_ALINKS=1,1708TU
RPT_AUTOPATCHUP=0
– 8 variables
– Hungup ‘Zap/pseudo-1149672235’
Node Variable dump for node 27021:
RPT_TXKEYED=0
RPT_ETXKEYED=0
RPT_RXKEYED=0
RPT_NUMLINKS=1
RPT_LINKS=1,T1708
RPT_NUMALINKS=1
RPT_ALINKS=1,1708TU
RPT_AUTOPATCHUP=0
– 8 variables
rxkeyed should go to zero and then txkeyed will go to 0
Ken
Check and check reset the set up fob was working right ptt my HT cw like every 10 mins but still cant connect to no one can connect to me?