# Issue with Hangup after first keying

**URL:** <https://community.allstarlink.org/t/issue-with-hangup-after-first-keying/10221>\
**Category:** AllStarLink\
**Created:** [July 3, 2013, 7:58pm UTC](https://community.allstarlink.org/t/issue-with-hangup-after-first-keying/10221 "2013-07-03T19:58:44Z")\
**Posts on this page:** 20\
**Page:** 1

<div class="post-metadata">

**Author:** ![Joshh](https://community.allstarlink.org/letter_avatar_proxy/v4/letter/j/8e8cbc/32.png) [@Joshh](https://community.allstarlink.org/u/Joshh)\
**Post date:** [July 3, 2013, 7:58pm UTC](https://community.allstarlink.org/t/issue-with-hangup-after-first-keying/10221/1 "2013-07-03T19:58:44Z")

</div>

Hello,

It is my first posting on here. I have ALMOST gotten the  
ACID installation working. I’m using the URI interfaced to ACID and to my  
radio. The asterisk can properly key the radio and its working just fine with  
that. I can also connect to the node with iaxRpt directly with no problem and  
transmit OUT of my radio.

However I am having some issues when my radio receives  
communication in that as soon as I get my first radio RX, asterisk will then  
play a tone out of the URI into the radio over and over again at about a one  
second interval. In the asterisk terminal it just keeps repeating:

– Hungup ‘Zap/pseudo-1726358622’

– Hungup ‘Zap/pseudo-1774817359’

– Hungup ‘Zap/pseudo-691532115’

– Hungup ‘Zap/pseudo-81389311’

– Hungup ‘Zap/pseudo-465154784’

– Hungup ‘Zap/pseudo-627058532’

– Hungup ‘Zap/pseudo-1656870264’

– Hungup ‘Zap/pseudo-1671691803’

– Hungup ‘Zap/pseudo-50274194’

forever keeping my radio always keyed.

I have the COR from the radio going into the URI. I do not  
plan on using CTCSS and have tried tying it to ground as well as tying it to  
the COR as well. My usbradio.conf has the following:

carrierfrom=usb

ctcssfrom=no

I have tried also ctcssfrom=usb as well.

Any help would be appreciated.

Thanks,

Josh

---

<div class="post-metadata">

**Author:** ![Benjamin](https://community.allstarlink.org/letter_avatar_proxy/v4/letter/b/3d9bf3/32.png) [@Benjamin](https://community.allstarlink.org/u/Benjamin)\
**Post date:** [July 3, 2013, 8:37pm UTC](https://community.allstarlink.org/t/issue-with-hangup-after-first-keying/10221/2 "2013-07-03T20:37:09Z")

</div>

sounds to me you are using a simplex node.

In your simpleusb.conf or usbradio.conf, ensure duplex=0, and not  
duplex=1. This is different from duplex= in rpt.conf

I had the same symptoms when I first setup my node.

Also, make sure you use the radio-tune-menu with a service monitor or  
some other methods to make sure your have good, clean audio being  
transmitted over the internet and over your node radio.

~Benjamin, KB9LFZ

> **···**
>
> On Wed, 2013-07-03 at 13:58 -0600, Joshua Hintze wrote:
> 
> > Hello,
> > 
> > It is my first posting on here. I have ALMOST gotten the ACID  
> > installation working. I'm using the URI interfaced to ACID and to my  
> > radio. The asterisk can properly key the radio and its working just  
> > fine with that. I can also connect to the node with iaxRpt directly  
> > with no problem and transmit OUT of my radio.
> > 
> > However I am having some issues when my radio receives communication  
> > in that as soon as I get my first radio RX, asterisk will then play a  
> > tone out of the URI into the radio over and over again at about a one  
> > second interval. In the asterisk terminal it just keeps repeating:
> > 
> > &nbsp;&nbsp;&nbsp;&nbsp;-- Hungup 'Zap/pseudo-1726358622'
> > 
> > &nbsp;&nbsp;&nbsp;&nbsp;-- Hungup 'Zap/pseudo-1774817359'
> > 
> > &nbsp;&nbsp;&nbsp;&nbsp;-- Hungup 'Zap/pseudo-691532115'
> > 
> > &nbsp;&nbsp;&nbsp;&nbsp;-- Hungup 'Zap/pseudo-81389311'
> > 
> > &nbsp;&nbsp;&nbsp;&nbsp;-- Hungup 'Zap/pseudo-465154784'
> > 
> > &nbsp;&nbsp;&nbsp;-- Hungup 'Zap/pseudo-627058532'
> > 
> > &nbsp;&nbsp;&nbsp;&nbsp;-- Hungup 'Zap/pseudo-1656870264'
> > 
> > &nbsp;&nbsp;&nbsp;&nbsp;-- Hungup 'Zap/pseudo-1671691803'
> > 
> > &nbsp;&nbsp;&nbsp;&nbsp;-- Hungup 'Zap/pseudo-50274194'
> > 
> > forever keeping my radio always keyed.
> > 
> > I have the COR from the radio going into the URI. I do not plan on  
> > using CTCSS and have tried tying it to ground as well as tying it to  
> > the COR as well. My usbradio.conf has the following:
> > 
> > carrierfrom=usb
> > 
> > ctcssfrom=no
> > 
> > I have tried also ctcssfrom=usb as well.
> > 
> > Any help would be appreciated.
> > 
> > Thanks,
> > 
> > Josh
> > 
> > \_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_  
> > App\_rpt-users mailing list  
> > App\_rpt-users@ohnosec.org  
> > [ohnosec.org](http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users)

---

<div class="post-metadata">

**Author:** ![Joshh](https://community.allstarlink.org/letter_avatar_proxy/v4/letter/j/8e8cbc/32.png) [@Joshh](https://community.allstarlink.org/u/Joshh)\
**Post date:** [July 3, 2013, 8:48pm UTC](https://community.allstarlink.org/t/issue-with-hangup-after-first-keying/10221/3 "2013-07-03T20:48:20Z")

</div>

Thanks Ben for the quick feedback. I think I might have figured it out. It turns out my COR signal might not necessarily be the best COR signal. It looks like the signal goes high on BOTH RX and TX. This is probably causing asterisk to think its receiving when its sending getting into a nice infinite loop.

I'm going to try an AND gate with the PTT so that PTT has to be high (i.e. NOT TX) and speaker mute (my COR) has to be high for a true COR output on RX.

In the meantime I tried carrierfrom=vox but it didn't really seem to work. Anybody get this working properly?

Thanks,

Josh

> **···**
>
> -----Original Message-----  
> From: Benjamin Naber [mailto:benjamin@kb9lfz.com]  
> Sent: Wednesday, July 03, 2013 2:37 PM  
> To: Joshua Hintze  
> Cc: app\_rpt-users@ohnosec.org  
> Subject: Re: [Bulk] [App\_rpt-users] Issue with Hangup after first keying
> 
> sounds to me you are using a simplex node.
> 
> In your simpleusb.conf or usbradio.conf, ensure duplex=0, and not  
> duplex=1. This is different from duplex= in rpt.conf
> 
> I had the same symptoms when I first setup my node.
> 
> Also, make sure you use the radio-tune-menu with a service monitor or  
> some other methods to make sure your have good, clean audio being  
> transmitted over the internet and over your node radio.
> 
> ~Benjamin, KB9LFZ
> 
> On Wed, 2013-07-03 at 13:58 -0600, Joshua Hintze wrote:
> 
> > Hello,
> > 
> > It is my first posting on here. I have ALMOST gotten the ACID  
> > installation working. I'm using the URI interfaced to ACID and to my  
> > radio. The asterisk can properly key the radio and its working just  
> > fine with that. I can also connect to the node with iaxRpt directly  
> > with no problem and transmit OUT of my radio.
> > 
> > However I am having some issues when my radio receives communication  
> > in that as soon as I get my first radio RX, asterisk will then play a  
> > tone out of the URI into the radio over and over again at about a one  
> > second interval. In the asterisk terminal it just keeps repeating:
> > 
> > &nbsp;&nbsp;&nbsp;&nbsp;-- Hungup 'Zap/pseudo-1726358622'
> > 
> > &nbsp;&nbsp;&nbsp;&nbsp;-- Hungup 'Zap/pseudo-1774817359'
> > 
> > &nbsp;&nbsp;&nbsp;&nbsp;-- Hungup 'Zap/pseudo-691532115'
> > 
> > &nbsp;&nbsp;&nbsp;&nbsp;-- Hungup 'Zap/pseudo-81389311'
> > 
> > &nbsp;&nbsp;&nbsp;&nbsp;-- Hungup 'Zap/pseudo-465154784'
> > 
> > &nbsp;&nbsp;&nbsp;-- Hungup 'Zap/pseudo-627058532'
> > 
> > &nbsp;&nbsp;&nbsp;&nbsp;-- Hungup 'Zap/pseudo-1656870264'
> > 
> > &nbsp;&nbsp;&nbsp;&nbsp;-- Hungup 'Zap/pseudo-1671691803'
> > 
> > &nbsp;&nbsp;&nbsp;&nbsp;-- Hungup 'Zap/pseudo-50274194'
> > 
> > forever keeping my radio always keyed.
> > 
> > I have the COR from the radio going into the URI. I do not plan on  
> > using CTCSS and have tried tying it to ground as well as tying it to  
> > the COR as well. My usbradio.conf has the following:
> > 
> > carrierfrom=usb
> > 
> > ctcssfrom=no
> > 
> > I have tried also ctcssfrom=usb as well.
> > 
> > Any help would be appreciated.
> > 
> > Thanks,
> > 
> > Josh
> > 
> > \_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_  
> > App\_rpt-users mailing list  
> > App\_rpt-users@ohnosec.org  
> > [ohnosec.org](http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users)

---

<div class="post-metadata">

**Author:** ![Benjamin](https://community.allstarlink.org/letter_avatar_proxy/v4/letter/b/3d9bf3/32.png) [@Benjamin](https://community.allstarlink.org/u/Benjamin)\
**Post date:** [July 3, 2013, 10:17pm UTC](https://community.allstarlink.org/t/issue-with-hangup-after-first-keying/10221/4 "2013-07-03T22:17:59Z")

</div>

I used carrierfrom=dsp and ctcssfrom=dsp

I am not sure why folks are having serious issues with that, but it  
works very well, and I have zero issues with it. I do crude signal  
testing with it, and even when the signal from the node radio is choppy,  
I can still command the node to do things.

I would say the biggest hurdle for getting DSP to work correctly is  
using the radio-tune-menu with a service monitor. This is to ensure the  
input and output audio audio levels are correctly set, and the DSP  
functions can understand the different audio freqs coming to it.

I do not use a COR/COS and the node does all the CTCSS stuff. Just TX/RX  
audio, and PTT connections are made to the node radio.

for the radio that requires 5V or active HIGH, use the K0KN PLRI  
interface. Very simple: a couple resistors and transistors. No need to  
waste time modifying a USB sound FOB, which is difficult to do because  
of the size of components one would be working with.

~Benjamin, KB9LFZ

> **···**
>
> On Wed, 2013-07-03 at 14:48 -0600, Joshua Hintze wrote:
> 
> > Thanks Ben for the quick feedback. I think I might have figured it out. It turns out my COR signal might not necessarily be the best COR signal. It looks like the signal goes high on BOTH RX and TX. This is probably causing asterisk to think its receiving when its sending getting into a nice infinite loop.
> > 
> > I'm going to try an AND gate with the PTT so that PTT has to be high (i.e. NOT TX) and speaker mute (my COR) has to be high for a true COR output on RX.
> > 
> > In the meantime I tried carrierfrom=vox but it didn't really seem to work. Anybody get this working properly?
> > 
> > Thanks,
> > 
> > Josh
> > 
> > -----Original Message-----  
> > From: Benjamin Naber [mailto:benjamin@kb9lfz.com]  
> > Sent: Wednesday, July 03, 2013 2:37 PM  
> > To: Joshua Hintze  
> > Cc: app\_rpt-users@ohnosec.org  
> > Subject: Re: [Bulk] [App\_rpt-users] Issue with Hangup after first keying
> > 
> > sounds to me you are using a simplex node.
> > 
> > In your simpleusb.conf or usbradio.conf, ensure duplex=0, and not  
> > duplex=1. This is different from duplex= in rpt.conf
> > 
> > I had the same symptoms when I first setup my node.
> > 
> > Also, make sure you use the radio-tune-menu with a service monitor or  
> > some other methods to make sure your have good, clean audio being  
> > transmitted over the internet and over your node radio.
> > 
> > ~Benjamin, KB9LFZ
> > 
> > On Wed, 2013-07-03 at 13:58 -0600, Joshua Hintze wrote:  
> > \> Hello,  
> > \>  
> > \>  
> > \>  
> > \> It is my first posting on here. I have ALMOST gotten the ACID  
> > \> installation working. I'm using the URI interfaced to ACID and to my  
> > \> radio. The asterisk can properly key the radio and its working just  
> > \> fine with that. I can also connect to the node with iaxRpt directly  
> > \> with no problem and transmit OUT of my radio.  
> > \>  
> > \>  
> > \>  
> > \> However I am having some issues when my radio receives communication  
> > \> in that as soon as I get my first radio RX, asterisk will then play a  
> > \> tone out of the URI into the radio over and over again at about a one  
> > \> second interval. In the asterisk terminal it just keeps repeating:  
> > \>  
> > \>  
> > \>  
> > \> -- Hungup 'Zap/pseudo-1726358622'  
> > \>  
> > \> -- Hungup 'Zap/pseudo-1774817359'  
> > \>  
> > \> -- Hungup 'Zap/pseudo-691532115'  
> > \>  
> > \> -- Hungup 'Zap/pseudo-81389311'  
> > \>  
> > \> -- Hungup 'Zap/pseudo-465154784'  
> > \>  
> > \> -- Hungup 'Zap/pseudo-627058532'  
> > \>  
> > \> -- Hungup 'Zap/pseudo-1656870264'  
> > \>  
> > \> -- Hungup 'Zap/pseudo-1671691803'  
> > \>  
> > \> -- Hungup 'Zap/pseudo-50274194'  
> > \>  
> > \>  
> > \>  
> > \> forever keeping my radio always keyed.  
> > \>  
> > \>  
> > \>  
> > \> I have the COR from the radio going into the URI. I do not plan on  
> > \> using CTCSS and have tried tying it to ground as well as tying it to  
> > \> the COR as well. My usbradio.conf has the following:  
> > \>  
> > \>  
> > \>  
> > \> carrierfrom=usb  
> > \>  
> > \> ctcssfrom=no  
> > \>  
> > \>  
> > \>  
> > \> I have tried also ctcssfrom=usb as well.  
> > \>  
> > \>  
> > \>  
> > \> Any help would be appreciated.  
> > \>  
> > \>  
> > \>  
> > \> Thanks,  
> > \>  
> > \>  
> > \>  
> > \> Josh  
> > \>  
> > \>  
> > \> \_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_  
> > \> App\_rpt-users mailing list  
> > \> App\_rpt-users@ohnosec.org  
> > \> [ohnosec.org](http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users)

---

<div class="post-metadata">

**Author:** ![Wb3awj](https://community.allstarlink.org/letter_avatar_proxy/v4/letter/w/8c91f0/32.png) [@Wb3awj](https://community.allstarlink.org/u/Wb3awj)\
**Post date:** [July 3, 2013, 11:29pm UTC](https://community.allstarlink.org/t/issue-with-hangup-after-first-keying/10221/5 "2013-07-03T23:29:15Z")

</div>

I too would suggest using the DSP.

Sure is easier to bring out discriminator audio than muck about building extra logic.

As to not using PL… please reconsider.

It’s quite frustrating to be connected to a large network and hearing the squelch on one node popping because of local noise or band conditions. Meanwhile, the DSP generally does a good job of decoding it.

> **···**
>
> –
> 
> Sent from my Android phone with K-9 Mail. Please excuse my brevity.

---

<div class="post-metadata">

**Author:** ![Joshh](https://community.allstarlink.org/letter_avatar_proxy/v4/letter/j/8e8cbc/32.png) [@Joshh](https://community.allstarlink.org/u/Joshh)\
**Post date:** [July 3, 2013, 11:37pm UTC](https://community.allstarlink.org/t/issue-with-hangup-after-first-keying/10221/6 "2013-07-03T23:37:38Z")

</div>

Thank you for all the suggestions thus far.

I'm using an ICOM IC-A110 VHF radio. I was able to find some  
schematics/block diagrams in the service manual here:

> **[Elektrotanya for electronics experts](https://elektrotanya.com/icom_ic-a110,_a110e_service_manual.pdf/download.html)**
>
> Electronics forum for electronics experts to repair defective appliance.

This is my first time trying to dig through a radio and find a COR. I'm not  
sure either where to get a discriminator audio signal either.

Josh

> **···**
>
> -----Original Message-----  
> From: Bryan D. Boyle [mailto:bdboyle@bdboyle.com]  
> Sent: Wednesday, July 03, 2013 3:29 PM  
> To: Joshua Hintze  
> Subject: Re: [App\_rpt-users] [Bulk] Issue with Hangup after first keying
> 
> On 7/3/2013 4:48 PM, Joshua Hintze wrote:
> 
> > Thanks Ben for the quick feedback. I think I might have figured it out. It
> 
> turns out my COR signal might not necessarily be the best COR signal. It  
> looks like the signal goes high on BOTH RX and TX. This is probably causing  
> asterisk to think its receiving when its sending getting into a nice  
> infinite loop.
> 
> > 
> 
> Then you don't have a true COR signal. What radio (make/model) are you  
> using? Can you get discriminator audio?? If so, you can use dsp to  
> derive COR; otherwise, you need to look elsewhere. Sounds like you're  
> too far down the circuit.
> 
> > I'm going to try an AND gate with the PTT so that PTT has to be high (i.e.
> 
> NOT TX) and speaker mute (my COR) has to be high for a true COR output on  
> RX.
> 
> > 
> 
> Sounds complicated; I'm thinking some quality time with the schematic  
> will provide an answer that is more agreeable and doesn't require  
> building logic circuits. In all the machines I've built the most  
> complex interface has been a pullup resistor on the DB25 connector. And  
> that's for everything from a micor to wouxun HTs to maxtracs and gtx's  
> and systel, and ALinco radio-based repeaters. And throw in a couple GE  
> rigs (Mastr-IIs) along the way. Heck, I even interfaced a TR-33C as a  
> receiver in a pinch.
> 
> > In the meantime I tried carrierfrom=vox but it didn't really seem to work.
> 
> Anybody get this working properly?
> 
> > 
> 
> As our Maximum Leader Jim says: "Friends don't let friends use VOX".  
> Not a way to do it; and is an artifact of development.
> 
> BB WB0YLE  
> Allstar 27294, 27295, 27673, 27710, etc.

---

<div class="post-metadata">

**Author:** ![Wb3awj](https://community.allstarlink.org/letter_avatar_proxy/v4/letter/w/8c91f0/32.png) [@Wb3awj](https://community.allstarlink.org/u/Wb3awj)\
**Post date:** [July 3, 2013, 11:46pm UTC](https://community.allstarlink.org/t/issue-with-hangup-after-first-keying/10221/7 "2013-07-03T23:46:09Z")

</div>

Try the top of either the volume or squelch controls.

> **···**
>
> Joshua Hintze [joshh@imsar.com](mailto:joshh@imsar.com) wrote:
> 
> > ```auto
> > Thank you for all the suggestions thus far.
> > 
> > I'm using an ICOM IC-A110 VHF radio. I was able to find some
> > schematics/block diagrams in the service manual here:
> > 
> > [http://elektrotanya.com/icom_ic-a110,_a110e_service_manual.pdf/download.html](http://elektrotanya.com/icom_ic-a110,_a110e_service_manual.pdf/download.html)
> > 
> > This is my first time trying to dig through a radio and find a COR. I'm not
> > sure either where to get a discriminator audio signal either.
> > 
> > Josh
> > 
> > -----Original Message-----
> > From: Bryan D. Boyle [mailto:bdboyle@bdboyle.com]
> > Sent: Wednesday, July 03, 2013 3:29 PM
> > To: Joshua Hintze
> > Subject: Re: [App_rpt-users] [Bulk] Issue with Hangup after first keying
> > 
> > On 7/3/2013 4:48 PM, Joshua Hintze wrote:
> > > Thanks Ben for the quick feedback. I think I might have figured it out. It
> > turns out my COR signal might not necessarily be the best COR signal. It
> > looks like the signal goes high on BOTH RX and TX. This is probably causing
> > asterisk to think its receiving when its sending getting into a nice
> > infinite loop.
> > 
> > Then you don't have a true COR signal. What radio (make/model) are you
> > using? Can you get discriminator audio?? If so, you can use dsp to
> > derive COR; otherwise, you need to look elsewhere. Sounds like you're
> > too far down the circuit.
> > 
> > > I'm going to try an AND gate with the PTT so that PTT has to be high (i.e.
> > NOT TX) and speaker mute (my COR) has to be high for a true COR output on
> > RX.
> > 
> > Sounds
> > complicated; I'm thinking some quality time with the schematic
> > will provide an answer that is more agreeable and doesn't require
> > building logic circuits. In all the machines I've built the most
> > complex interface has been a pullup resistor on the DB25 connector. And
> > that's for everything from a micor to wouxun HTs to maxtracs and gtx's
> > and systel, and ALinco radio-based repeaters. And throw in a couple GE
> > rigs (Mastr-IIs) along the way. Heck, I even interfaced a TR-33C as a
> > receiver in a pinch.
> > 
> > > In the meantime I tried carrierfrom=vox but it didn't really seem to work.
> > Anybody get this working properly?
> > 
> > As our Maximum Leader Jim says: "Friends don't let friends use VOX".
> > Not a way to do it; and is an artifact of development.
> > 
> > BB WB0YLE
> > Allstar 27294, 27295, 27673,
> > 27710, etc.
> > 
> > ---
> > 
> > App_rpt-users mailing list
> > App_rpt-users@ohnosec.org
> > [http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users](http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users)
> > 
> > ```
> 
> –
> 
> Sent from my Android phone with K-9 Mail. Please excuse my brevity.

---

<div class="post-metadata">

**Author:** ![Wb3awj](https://community.allstarlink.org/letter_avatar_proxy/v4/letter/w/8c91f0/32.png) [@Wb3awj](https://community.allstarlink.org/u/Wb3awj)\
**Post date:** [July 4, 2013, 12:01am UTC](https://community.allstarlink.org/t/issue-with-hangup-after-first-keying/10221/8 "2013-07-04T00:01:33Z")

</div>

Ahh… now I understand… aircraft AM?

Looking at the block diagram, does the output of IC11, the squelch switch do what you want for COR?

> **···**
>
> –
> 
> Sent from my Android phone with K-9 Mail. Please excuse my brevity.

---

<div class="post-metadata">

**Author:** ![Joshh](https://community.allstarlink.org/letter_avatar_proxy/v4/letter/j/8e8cbc/32.png) [@Joshh](https://community.allstarlink.org/u/Joshh)\
**Post date:** [July 4, 2013, 12:06am UTC](https://community.allstarlink.org/t/issue-with-hangup-after-first-keying/10221/9 "2013-07-04T00:06:29Z")

</div>

I did not see that one. Thanks for pointing it out. I will test  
it out tomorrow when I get back into work.

Josh

**From:**  
[app\_rpt-users-bounces@ohnosec.org](mailto:app_rpt-users-bounces@ohnosec.org) [[mailto:app\_rpt-users-bounces@ohnosec.org](mailto:app_rpt-users-bounces@ohnosec.org)] **On  
Behalf Of** Robert a. Poff

> **···**
>
> **Sent:** Wednesday, July 03, 2013 6:02 PM  
> **To:** [app\_rpt-users@ohnosec.org](mailto:app_rpt-users@ohnosec.org)  
> **Subject:** Re: [App\_rpt-users] [Bulk] Issue with Hangup after first keying
> 
> Ahh… now I understand… aircraft AM?
> 
> Looking at the block diagram, does the output of IC11, the squelch switch do  
> what you want for COR?
> 
> –
> 
> Sent from my Android phone with K-9 Mail. Please excuse my brevity.

---

<div class="post-metadata">

**Author:** ![W8VT](https://community.allstarlink.org/user_avatar/community.allstarlink.org/w8vt/32/511_2.png) [@W8VT](https://community.allstarlink.org/u/W8VT)\
**Post date:** [July 4, 2013, 1:40am UTC](https://community.allstarlink.org/t/issue-with-hangup-after-first-keying/10221/10 "2013-07-04T01:40:12Z")

</div>

The Icom IC-A110 is an AM aircraft radio. Being AM there is no discriminator audio, and DSP derived COR won't work due to the nature of the AM signal. You're going to have to dig around in the squelch circuit to find a point that toggles. Most AM type squelch are usually derived from the AGC. Don't what they're doing in the Icom.

Ed, W8VT  
Nodes 27849 29496  
Beckley WV

> **···**
>
> On 07/03/2013 07:37 PM, Joshua Hintze wrote:
> 
> > Thank you for all the suggestions thus far.
> > 
> > I'm using an ICOM IC-A110 VHF radio. I was able to find some  
> > schematics/block diagrams in the service manual here:
> > 
> > [ICOM IC-A110, A110E SERVICE MANUAL Service Manual download, schematics, eeprom, repair info for electronics experts](http://elektrotanya.com/icom_ic-a110,_a110e_service_manual.pdf/download.html)
> > 
> > This is my first time trying to dig through a radio and find a COR. I'm not  
> > sure either where to get a discriminator audio signal either.
> > 
> > Josh
> > 
> > -----Original Message-----  
> > From: Bryan D. Boyle [mailto:bdboyle@bdboyle.com]  
> > Sent: Wednesday, July 03, 2013 3:29 PM  
> > To: Joshua Hintze  
> > Subject: Re: [App\_rpt-users] [Bulk] Issue with Hangup after first keying
> > 
> > On 7/3/2013 4:48 PM, Joshua Hintze wrote:
> > 
> > > Thanks Ben for the quick feedback. I think I might have figured it out. It
> > 
> > turns out my COR signal might not necessarily be the best COR signal. It  
> > looks like the signal goes high on BOTH RX and TX. This is probably causing  
> > asterisk to think its receiving when its sending getting into a nice  
> > infinite loop.  
> > Then you don't have a true COR signal. What radio (make/model) are you  
> > using? Can you get discriminator audio?? If so, you can use dsp to  
> > derive COR; otherwise, you need to look elsewhere. Sounds like you're  
> > too far down the circuit.
> > 
> > > I'm going to try an AND gate with the PTT so that PTT has to be high (i.e.
> > 
> > NOT TX) and speaker mute (my COR) has to be high for a true COR output on  
> > RX.  
> > Sounds complicated; I'm thinking some quality time with the schematic  
> > will provide an answer that is more agreeable and doesn't require  
> > building logic circuits. In all the machines I've built the most  
> > complex interface has been a pullup resistor on the DB25 connector. And  
> > that's for everything from a micor to wouxun HTs to maxtracs and gtx's  
> > and systel, and ALinco radio-based repeaters. And throw in a couple GE  
> > rigs (Mastr-IIs) along the way. Heck, I even interfaced a TR-33C as a  
> > receiver in a pinch.
> > 
> > > In the meantime I tried carrierfrom=vox but it didn't really seem to work.
> > 
> > Anybody get this working properly?  
> > As our Maximum Leader Jim says: "Friends don't let friends use VOX".  
> > Not a way to do it; and is an artifact of development.
> > 
> > BB WB0YLE  
> > Allstar 27294, 27295, 27673, 27710, etc.
> > 
> > \_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_  
> > App\_rpt-users mailing list  
> > App\_rpt-users@ohnosec.org  
> > [ohnosec.org](http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users)

---

<div class="post-metadata">

**Author:** ![Bryan\_D\_Boyle](https://community.allstarlink.org/user_avatar/community.allstarlink.org/bryan_d_boyle/32/22_2.png) [@Bryan\_D\_Boyle](https://community.allstarlink.org/u/Bryan_D_Boyle)\
**Post date:** [July 4, 2013, 3:17am UTC](https://community.allstarlink.org/t/issue-with-hangup-after-first-keying/10221/11 "2013-07-04T03:17:53Z")

</div>

Detecting squelch break in AM is a lot different that breaking squelch  
in FM...

iirc, you have to depend on the AGC circuit to do what it's supposed to  
do in order to detect a signal level delta greater than the background  
hash, which is a variable. FM looks for the detector to open up when  
the frequency swing happens...a bit more binary than AM transmissions,  
which means there's a constant noise level vice AM (just listen on the  
HF bands to see the difference in the noise levels from minute to  
minute...). Kind of hard to detect amplitude changes as being a  
legitimate carrier vice noise, since they're both the same general  
modulation envelope, whereas in FM, the intelligence is carried in a  
different mode than the background noise.

Don't know whether I'm explaining it clearly enough, but it's in that  
general neighborhood or some such.

Just what are you trying to do?

BB

> **···**
>
> On 7/3/2013 7:37 PM, Joshua Hintze wrote:
> 
> > Thank you for all the suggestions thus far.
> > 
> > I'm using an ICOM IC-A110 VHF radio. I was able to find some  
> > schematics/block diagrams in the service manual here:
> > 
> > [ICOM IC-A110, A110E SERVICE MANUAL Service Manual download, schematics, eeprom, repair info for electronics experts](http://elektrotanya.com/icom_ic-a110,_a110e_service_manual.pdf/download.html)
> > 
> > This is my first time trying to dig through a radio and find a COR. I'm not  
> > sure either where to get a discriminator audio signal either.

---

<div class="post-metadata">

**Author:** ![wbs0991](https://community.allstarlink.org/letter_avatar_proxy/v4/letter/w/eb9ed0/32.png) [@wbs0991](https://community.allstarlink.org/u/wbs0991)\
**Post date:** [July 4, 2013, 11:58am UTC](https://community.allstarlink.org/t/issue-with-hangup-after-first-keying/10221/12 "2013-07-04T11:58:08Z")

</div>

Joshua, I’m going to take a chance here and state what seems to be the obvious; all your additional work to get your node functional seem to stem from the rather unusual radio you are using. So why not just bite the bullet and change radios to something a bit more standard, like a ham dual-band FM radio for some flexability, or maybe a ham monoband HT or mobile radio to save both time and money? Seems the time and effort you have put into getting the AM aircraft radio to function would be moot with just about any ham FM radio replacing it. And if you get one with a data-access conection, all the signals you need are there so you can run COR or stratight audio relatively easily, whatever your choice? Or have I missed something obvious related to your choice of radios? Just a thought.

> **···**
>
> — On \*\* Wed, 7/3/13, Joshua Hintze _[joshh@imsar.com](mailto:joshh@imsar.com)_\*\* wrote:
> 
> > From: Joshua Hintze [joshh@imsar.com](mailto:joshh@imsar.com)  
> > Subject: Re: [App\_rpt-users] [Bulk] Issue with Hangup after first keying  
> > To: “‘Benjamin Naber’” [benjamin@kb9lfz.com](mailto:benjamin@kb9lfz.com)  
> > Cc: [app\_rpt-users@ohnosec.org](mailto:app_rpt-users@ohnosec.org)  
> > Date: Wednesday, July 3, 2013, 8:48 PM
> > 
> > Thanks Ben for the quick feedback. I think I might have figured it out. It turns out my COR signal might not necessarily be the best COR signal. It looks like the signal goes high on BOTH RX and TX. This is probably causing asterisk to think its receiving when its sending getting into a nice infinite loop.
> > 
> > I’m going to try an AND gate with the PTT so that PTT has to be high (i.e. NOT TX) and speaker mute (my COR) has to be high for a true COR output on RX.
> > 
> > In the meantime I tried carrierfrom=vox but it didn’t really seem to work. Anybody get this working properly?
> > 
> > Thanks,
> > 
> > Josh
> > 
> > -----Original Message-----  
> > From: Benjamin Naber [mailto:[benjamin@kb9lfz.com](http://us.mc1614.mail.yahoo.com/mc/compose?to=benjamin@kb9lfz.com)]  
> > Sent: Wednesday, July 03, 2013 2:37 PM  
> > To: Joshua Hintze  
> > Cc: [app\_rpt-users@ohnosec.org](http://us.mc1614.mail.yahoo.com/mc/compose?to=app_rpt-users@ohnosec.org)  
> > Subject: Re: [Bulk] [App\_rpt-users] Issue with Hangup after first keying
> > 
> > sounds to me you are using a simplex node.
> > 
> > In your simpleusb.conf or usbradio.conf, ensure duplex=0, and not  
> > duplex=1. This is different from duplex= in rpt.conf
> > 
> > I had the same symptoms when I first setup my node.
> > 
> > Also, make sure you use the radio-tune-menu with a service monitor or  
> > some other methods to make sure your have good, clean audio being  
> > transmitted over the internet and over your node radio.
> > 
> > ~Benjamin, KB9LFZ
> > 
> > On Wed, 2013-07-03 at 13:58 -0600, Joshua Hintze wrote:
> > 
> > > Hello,
> > > 
> > > It is my first posting on here. I have ALMOST gotten the ACID  
> > > installation working. I’m using the URI interfaced to ACID and to  
> > > my  
> > > radio. The asterisk can properly key the radio and its working just  
> > > fine with that. I can also connect to the node with iaxRpt directly  
> > > with no problem and transmit OUT of my radio.
> > > 
> > > However I am having some issues when my radio receives communication  
> > > in that as soon as I get my first radio RX, asterisk will then play a  
> > > tone out of the URI into the radio over and over again at about a one  
> > > second interval. In the asterisk terminal it just keeps repeating:
> > > 
> > > ```
> > > -- Hungup 'Zap/pseudo-1726358622'
> > > 
> > > -- Hungup 'Zap/pseudo-1774817359'
> > > 
> > > -- Hungup 'Zap/pseudo-691532115'
> > > 
> > > -- Hungup 'Zap/pseudo-81389311'
> > > 
> > > -- Hungup 'Zap/pseudo-465154784'
> > > 
> > > ```
> > 
> > – Hungup ‘Zap/pseudo-627058532’
> > 
> > > ```
> > > -- Hungup 'Zap/pseudo-1656870264'
> > > 
> > > -- Hungup 'Zap/pseudo-1671691803'
> > > 
> > > -- Hungup 'Zap/pseudo-50274194'
> > > 
> > > ```
> > > 
> > > forever keeping my radio always keyed.
> > > 
> > > I have the COR from the radio going into the URI. I do not plan on  
> > > using CTCSS and have tried tying it to ground as well as tying it to  
> > > the COR as well. My usbradio.conf has the following:
> > > 
> > > carrierfrom=usb
> > > 
> > > ctcssfrom=no
> > > 
> > > I have tried also ctcssfrom=usb as well.
> > > 
> > > Any help would be appreciated.
> > > 
> > > Thanks,
> > > 
> > > Josh
> > 
> > * * *
> > 
> > > App\_rpt-users mailing list  
> > > [App\_rpt-users@ohnosec.org](http://us.mc1614.mail.yahoo.com/mc/compose?to=App_rpt-users@ohnosec.org)  
> > > [http://ohnosec.org/cgi-bin/mailman/listinfo/app\_rpt-users](http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users)
> > 
> > * * *
> > 
> > App\_rpt-users mailing list  
> > [App\_rpt-users@ohnosec.org](http://us.mc1614.mail.yahoo.com/mc/compose?to=App_rpt-users@ohnosec.org)  
> > [http://ohnosec.org/cgi-bin/mailman/listinfo/app\_rpt-users](http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users)

---

<div class="post-metadata">

**Author:** ![n3fe](https://community.allstarlink.org/letter_avatar_proxy/v4/letter/n/85e7bf/32.png) [@n3fe](https://community.allstarlink.org/u/n3fe)\
**Post date:** [July 4, 2013, 2:48pm UTC](https://community.allstarlink.org/t/issue-with-hangup-after-first-keying/10221/13 "2013-07-04T14:48:02Z")

</div>

Are you running full duplex on a simplex radio?

Corey N3FE

> **···**
>
> \_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_  
> From: [app\_rpt-users-bounces@ohnosec.org](mailto:app_rpt-users-bounces@ohnosec.org) [app\_rpt-users-bounces@ohnosec.org] On Behalf Of Joshua Hintze [joshh@imsar.com]  
> Sent: Wednesday, July 03, 2013 3:58 PM  
> To: [app\_rpt-users@ohnosec.org](mailto:app_rpt-users@ohnosec.org)  
> Subject: [App\_rpt-users] Issue with Hangup after first keying
> 
> Hello,
> 
> It is my first posting on here. I have ALMOST gotten the ACID installation working. I'm using the URI interfaced to ACID and to my radio. The asterisk can properly key the radio and its working just fine with that. I can also connect to the node with iaxRpt directly with no problem and transmit OUT of my radio.
> 
> However I am having some issues when my radio receives communication in that as soon as I get my first radio RX, asterisk will then play a tone out of the URI into the radio over and over again at about a one second interval. In the asterisk terminal it just keeps repeating:
> 
> &nbsp;&nbsp;&nbsp;&nbsp;-- Hungup 'Zap/pseudo-1726358622'  
> &nbsp;&nbsp;&nbsp;&nbsp;-- Hungup 'Zap/pseudo-1774817359'  
> &nbsp;&nbsp;&nbsp;&nbsp;-- Hungup 'Zap/pseudo-691532115'  
> &nbsp;&nbsp;&nbsp;&nbsp;-- Hungup 'Zap/pseudo-81389311'  
> &nbsp;&nbsp;&nbsp;&nbsp;-- Hungup 'Zap/pseudo-465154784'  
> &nbsp;&nbsp;&nbsp;-- Hungup 'Zap/pseudo-627058532'  
> &nbsp;&nbsp;&nbsp;&nbsp;-- Hungup 'Zap/pseudo-1656870264'  
> &nbsp;&nbsp;&nbsp;&nbsp;-- Hungup 'Zap/pseudo-1671691803'  
> &nbsp;&nbsp;&nbsp;&nbsp;-- Hungup 'Zap/pseudo-50274194'
> 
> forever keeping my radio always keyed.
> 
> I have the COR from the radio going into the URI. I do not plan on using CTCSS and have tried tying it to ground as well as tying it to the COR as well. My usbradio.conf has the following:
> 
> carrierfrom=usb  
> ctcssfrom=no
> 
> I have tried also ctcssfrom=usb as well.
> 
> Any help would be appreciated.
> 
> Thanks,
> 
> Josh
> 
> --  
> This message was scanned and is believed to be clean.  
> Click here to report this message as spam.\<[http://simba.repeater.net:8080/cgi-bin/learn-msg.cgi?id=6EF48221A.A93BD](http://simba.repeater.net:8080/cgi-bin/learn-msg.cgi?id=6EF48221A.A93BD)\>

---

<div class="post-metadata">

**Author:** ![n3fe](https://community.allstarlink.org/letter_avatar_proxy/v4/letter/n/85e7bf/32.png) [@n3fe](https://community.allstarlink.org/u/n3fe)\
**Post date:** [July 4, 2013, 2:52pm UTC](https://community.allstarlink.org/t/issue-with-hangup-after-first-keying/10221/14 "2013-07-04T14:52:36Z")

</div>

Forget this emaill. I should learn to read all my emails before replying to an old one...

Corey N3FE

> **···**
>
> \_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_  
> From: [app\_rpt-users-bounces@ohnosec.org](mailto:app_rpt-users-bounces@ohnosec.org) [app\_rpt-users-bounces@ohnosec.org] On Behalf Of Corey Dean [n3fe@repeater.net]  
> Sent: Thursday, July 04, 2013 10:48 AM  
> To: Joshua Hintze; [app\_rpt-users@ohnosec.org](mailto:app_rpt-users@ohnosec.org)  
> Subject: Re: [App\_rpt-users] Issue with Hangup after first keying
> 
> Are you running full duplex on a simplex radio?
> 
> Corey N3FE  
> \_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_  
> From: [app\_rpt-users-bounces@ohnosec.org](mailto:app_rpt-users-bounces@ohnosec.org) [app\_rpt-users-bounces@ohnosec.org] On Behalf Of Joshua Hintze [joshh@imsar.com]  
> Sent: Wednesday, July 03, 2013 3:58 PM  
> To: [app\_rpt-users@ohnosec.org](mailto:app_rpt-users@ohnosec.org)  
> Subject: [App\_rpt-users] Issue with Hangup after first keying
> 
> Hello,
> 
> It is my first posting on here. I have ALMOST gotten the ACID installation working. I'm using the URI interfaced to ACID and to my radio. The asterisk can properly key the radio and its working just fine with that. I can also connect to the node with iaxRpt directly with no problem and transmit OUT of my radio.
> 
> However I am having some issues when my radio receives communication in that as soon as I get my first radio RX, asterisk will then play a tone out of the URI into the radio over and over again at about a one second interval. In the asterisk terminal it just keeps repeating:
> 
> &nbsp;&nbsp;&nbsp;&nbsp;-- Hungup 'Zap/pseudo-1726358622'  
> &nbsp;&nbsp;&nbsp;&nbsp;-- Hungup 'Zap/pseudo-1774817359'  
> &nbsp;&nbsp;&nbsp;&nbsp;-- Hungup 'Zap/pseudo-691532115'  
> &nbsp;&nbsp;&nbsp;&nbsp;-- Hungup 'Zap/pseudo-81389311'  
> &nbsp;&nbsp;&nbsp;&nbsp;-- Hungup 'Zap/pseudo-465154784'  
> &nbsp;&nbsp;&nbsp;-- Hungup 'Zap/pseudo-627058532'  
> &nbsp;&nbsp;&nbsp;&nbsp;-- Hungup 'Zap/pseudo-1656870264'  
> &nbsp;&nbsp;&nbsp;&nbsp;-- Hungup 'Zap/pseudo-1671691803'  
> &nbsp;&nbsp;&nbsp;&nbsp;-- Hungup 'Zap/pseudo-50274194'
> 
> forever keeping my radio always keyed.
> 
> I have the COR from the radio going into the URI. I do not plan on using CTCSS and have tried tying it to ground as well as tying it to the COR as well. My usbradio.conf has the following:
> 
> carrierfrom=usb  
> ctcssfrom=no
> 
> I have tried also ctcssfrom=usb as well.
> 
> Any help would be appreciated.
> 
> Thanks,
> 
> Josh
> 
> --  
> This message was scanned and is believed to be clean.  
> Click here to report this message as spam.\<[http://simba.repeater.net:8080/cgi-bin/learn-msg.cgi?id=6EF48221A.A93BD](http://simba.repeater.net:8080/cgi-bin/learn-msg.cgi?id=6EF48221A.A93BD)\>  
> \_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_  
> App\_rpt-users mailing list  
> [App\_rpt-users@ohnosec.org](mailto:App_rpt-users@ohnosec.org)  
> [http://ohnosec.org/cgi-bin/mailman/listinfo/app\_rpt-users](http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users)
> 
> --  
> This message was scanned and is believed to be clean.  
> Click here to report this message as spam.  
> [http://simba.repeater.net/cgi-bin/learn-msg.cgi?id=E2134221A.A8DD0](http://simba.repeater.net/cgi-bin/learn-msg.cgi?id=E2134221A.A8DD0)

---

<div class="post-metadata">

**Author:** ![Brett\_Friermood](https://community.allstarlink.org/user_avatar/community.allstarlink.org/brett_friermood/32/832_2.png) [@Brett\_Friermood](https://community.allstarlink.org/u/Brett_Friermood)\
**Post date:** [July 5, 2013, 4:17am UTC](https://community.allstarlink.org/t/issue-with-hangup-after-first-keying/10221/15 "2013-07-05T04:17:27Z")

</div>

Replacing the air band radio with an amateur grade FM radio would be rather useless when trying to communicate with aircraft on VHF-AM. I’m sure Josh has a perfectly valid reason for using that radio.

Brett KQ9N

> **···**
>
> On Thu, Jul 4, 2013 at 6:58 AM, Bill South [wbs099@yahoo.com](mailto:wbs099@yahoo.com) wrote:
> 
> > Joshua, I’m going to take a chance here and state what seems to be the obvious; all your additional work to get your node functional seem to stem from the rather unusual radio you are using. So why not just bite the bullet and change radios to something a bit more standard, like a ham dual-band FM radio for some flexability, or maybe a ham monoband HT or mobile radio to save both time and money? Seems the time and effort you have put into getting the AM aircraft radio to function would be moot with just about any ham FM radio replacing it. And if you get one with a data-access conection, all the signals you need are there so you can run COR or stratight audio relatively easily, whatever your choice? Or have I missed something obvious related to your choice of radios? Just a thought.

---

<div class="post-metadata">

**Author:** ![Bryan\_D\_Boyle](https://community.allstarlink.org/user_avatar/community.allstarlink.org/bryan_d_boyle/32/22_2.png) [@Bryan\_D\_Boyle](https://community.allstarlink.org/u/Bryan_D_Boyle)\
**Post date:** [July 5, 2013, 12:40pm UTC](https://community.allstarlink.org/t/issue-with-hangup-after-first-keying/10221/16 "2013-07-05T12:40:02Z")

</div>

Aware (painfully) of the diffferences, having owned a certificated (ie  
could yellow-tag nav/comm/xpdr/mb/ils/etc) avionics shop years  
ago...right about the time GPS came along (the KLN-88 was the hot  
navigation device way back then...).

As long as the proper precautions were taken to not cross-service  
connect...one service does not require an operator certificate (unless  
traveling outside the US, in which case a restricted radiotelephone op  
permit, IIRC, is required, though the aircraft station is licensed (call  
sign is the N number)), the other requires both an op and station license.

IOW, you can't use 122.9 (multicom) as a simplex channel to bring up  
your 145.25 repeater and talk to your mates....😉

Wasn't questioning what he was trying to do, just the mode, interface  
differences, and equipment that he was using to do so.

bb

> **···**
>
> On 7/5/2013 12:17 AM, Brett Friermood wrote:
> 
> > Replacing the air band radio with an amateur grade FM radio would be rather  
> > useless when trying to communicate with aircraft on VHF-AM. I'm sure Josh  
> > has a perfectly valid reason for using that radio.

---

<div class="post-metadata">

**Author:** ![Joshh](https://community.allstarlink.org/letter_avatar_proxy/v4/letter/j/8e8cbc/32.png) [@Joshh](https://community.allstarlink.org/u/Joshh)\
**Post date:** [July 5, 2013, 5:56pm UTC](https://community.allstarlink.org/t/issue-with-hangup-after-first-keying/10221/17 "2013-07-05T17:56:11Z")

</div>

Ok all I'm back to work today and playing with this setup again.

I was able to isolate a much better signal for COR than what I had before.  
This now truely goes from 0V-\>5V only when receiving and not when  
transmitting. However I'm still having issues.

As soon as asterisk receives a signal it immediately tries to transmit a  
signal out. This then effectively pulls the PTT low and my receiver stops  
receiving. It is almost like it is in duplex mode but I have in  
usbradio.conf

duplex=0 ; Full Duplex

rxondelay=0 ; Uncomment and/or adjust for simplex nodes to  
eliminate "Ping Ponging"  
&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;; or "Relay Racing".  
&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;; A positive value here will instruct the usbradio  
driver to ignore the  
&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;; COR line for a specified number of 20mSec  
intervals following the  
&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;; release of PTT. Use this only on simplex nodes,  
and leave commented  
&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;; out for repeaters or other full duplex nodes.  
eeprom=1

Just for clarity I'll post my entire usbradio.conf below:

[general]

[usb]

hdwtype=0 ; Leave this set to 0 for USB sound fobs modified  
using  
&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;; the instructions from usbfob.pdf. Use a setting of  
&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;; 1 is for Dingotel/Sph interfaces.

rxboost=1 ; 0 = 20db attenuator inserted, 1= 20db attenuator  
removed  
&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;; Set to 1 for additonal gain if using a low-level  
receiver output

rxctcssrelax=1 ; reduce talkoff from radios w/o CTCSS Tx HPF  
&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;; Do not change this, leave this as a 1

;txctcssdefault=100.0 ; default tx ctcss freq, any frequency permitted  
;rxctcssfreqs=100.0 ; rx ctcss freqs in floating point. must be in table  
;txctcssfreqs=100.0 ; tx ctcss freqs, any frequency permitted  
rxctcssoverride=1 ; Set to 1 or yes to start out in carrier squelch  
mode

carrierfrom=usb ; no,usb,usbinvert,dsp,vox  
&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;; no - no carrier detection at all  
&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;; usb - from the COR line on the modified USB sound  
fob  
&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;; usbinvert - from the inverted COR line on the  
modified USB sound fob  
&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;; dsp - from RX noise using dsp techniques  
&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;; vox - voice activated from RX audio

ctcssfrom=no ; no,usb,dsp  
&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;; no - CTCSS decoding, system will be carrier  
squelch  
&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;; usb - CTCSS decoding using input from USB FOB  
&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;; (currently not supported)  
&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;; dsp - CTCSS decoding using RX audio in DSP.  
&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;; rxdemod option must be set to flat for this to  
work.

rxdemod=speaker ; input type from radio: no,speaker,flat  
&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;; no - RX audio input not used  
&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;; flat - Use RX audio from discriminator (before  
de-emphasis)  
&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;; speaker - use de-emphasized audio

txprelim=no ; Audio processing on left output channel: no,yes  
&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;; no - Audio is not pre-emphasized and limited.  
&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;; Suitable for use on a microphone input  
&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;; yes - Audio is pre-emphasized and limited.  
&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;; Suitable for direct connection to an FM modulator

txlimonly=no ; Audio limiting with no pre-emphasis on output  
channel: no,yes  
&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;; no - Audio is not limited.  
&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;; yes - Audio is limited.  
&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;; Suitable for transmitters with no limiting but  
with pre-emphasis.

txtoctype=no ; Transmit tone control type: no,phase,notone  
&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;; no - CTCSS tone encoding with no hang time  
&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;; phase - encode CTCSS and reverse phase  
&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;; AKA ("reverse burst") before unkeying TX  
&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;; notone - encode CTCSS and stop sending tone before  
unkeying TX  
&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;; AKA ("chicken burst")

txmixa=voice ; Left channel output: no,voice,tone,composite,auxvoice  
&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;; no - Do not output anything  
&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;; voice - output voice only  
&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;; tone - CTCSS tone only  
&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;; composite - voice and tone  
&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;; auxvoice - auxiliary voice output at headphone  
level for monitoring

txmixb=no ; Right channel output: no,voice,tone,composite,  
auxvoice  
&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;; See txmixa above.

invertptt=0 ; Invert PTT 0 = ground to transmit, 1 = open to  
transmit  
&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;; This is the collector lead of the 2n4401 on the  
modified  
&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;; usb sound fob.  
&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;; please refer to the howto for the procedure to do  
this.

duplex=0 ; Full Duplex

rxondelay=0 ; Uncomment and/or adjust for simplex nodes to  
eliminate "Ping Ponging"  
&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;; or "Relay Racing".  
&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;; A positive value here will instruct the usbradio  
driver to ignore the  
&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;; COR line for a specified number of 20mSec  
intervals following the  
&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;; release of PTT. Use this only on simplex nodes,  
and leave commented  
&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;; out for repeaters or other full duplex nodes.  
eeprom=1

Any thoughts on why asterisk would be trying to send a signal as soon as it  
receives one? After the first time (upon asterisk restart) it receives a  
signal it sends a beep followed by a morse code sequence.

Thanks,

Josh

> **···**
>
> -----Original Message-----  
> From: Corey Dean [mailto:n3fe@repeater.net]  
> Sent: Thursday, July 04, 2013 8:48 AM  
> To: Joshua Hintze; app\_rpt-users@ohnosec.org  
> Subject: RE: [App\_rpt-users] Issue with Hangup after first keying
> 
> Are you running full duplex on a simplex radio?
> 
> Corey N3FE  
> \_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_  
> From: app\_rpt-users-bounces@ohnosec.org [app\_rpt-users-bounces@ohnosec.org]  
> On Behalf Of Joshua Hintze [joshh@imsar.com]  
> Sent: Wednesday, July 03, 2013 3:58 PM  
> To: app\_rpt-users@ohnosec.org  
> Subject: [App\_rpt-users] Issue with Hangup after first keying
> 
> Hello,
> 
> It is my first posting on here. I have ALMOST gotten the ACID installation  
> working. I'm using the URI interfaced to ACID and to my radio. The asterisk  
> can properly key the radio and its working just fine with that. I can also  
> connect to the node with iaxRpt directly with no problem and transmit OUT of  
> my radio.
> 
> However I am having some issues when my radio receives communication in that  
> as soon as I get my first radio RX, asterisk will then play a tone out of  
> the URI into the radio over and over again at about a one second interval.  
> In the asterisk terminal it just keeps repeating:
> 
> &nbsp;&nbsp;&nbsp;&nbsp;-- Hungup 'Zap/pseudo-1726358622'  
> &nbsp;&nbsp;&nbsp;&nbsp;-- Hungup 'Zap/pseudo-1774817359'  
> &nbsp;&nbsp;&nbsp;&nbsp;-- Hungup 'Zap/pseudo-691532115'  
> &nbsp;&nbsp;&nbsp;&nbsp;-- Hungup 'Zap/pseudo-81389311'  
> &nbsp;&nbsp;&nbsp;&nbsp;-- Hungup 'Zap/pseudo-465154784'  
> &nbsp;&nbsp;&nbsp;-- Hungup 'Zap/pseudo-627058532'  
> &nbsp;&nbsp;&nbsp;&nbsp;-- Hungup 'Zap/pseudo-1656870264'  
> &nbsp;&nbsp;&nbsp;&nbsp;-- Hungup 'Zap/pseudo-1671691803'  
> &nbsp;&nbsp;&nbsp;&nbsp;-- Hungup 'Zap/pseudo-50274194'
> 
> forever keeping my radio always keyed.
> 
> I have the COR from the radio going into the URI. I do not plan on using  
> CTCSS and have tried tying it to ground as well as tying it to the COR as  
> well. My usbradio.conf has the following:
> 
> carrierfrom=usb  
> ctcssfrom=no
> 
> I have tried also ctcssfrom=usb as well.
> 
> Any help would be appreciated.
> 
> Thanks,
> 
> Josh
> 
> --  
> This message was scanned and is believed to be clean.  
> Click here to report this message as  
> spam.\<[http://simba.repeater.net:8080/cgi-bin/learn-msg.cgi?id=6EF48221A.A93B](http://simba.repeater.net:8080/cgi-bin/learn-msg.cgi?id=6EF48221A.A93B)
> 
> >

---

<div class="post-metadata">

**Author:** ![N5zua](https://community.allstarlink.org/letter_avatar_proxy/v4/letter/n/ac91a4/32.png) [@N5zua](https://community.allstarlink.org/u/N5zua)\
**Post date:** [July 5, 2013, 6:05pm UTC](https://community.allstarlink.org/t/issue-with-hangup-after-first-keying/10221/18 "2013-07-05T18:05:16Z")

</div>

For a simplex node be sure that you have the following defined in:

/etc/asterisk/rpt.conf

duplex=0 (for no telemetry / messasges)

or

duplex=1 (enables telemetry / messages / courtesy tones)

This is a different setting than the duplex = in your usbradio.conf file

N5ZUA

> **···**
>
> ----- Original Message ----- From: "Joshua Hintze" \<joshh@imsar.com\>  
> To: "'Corey Dean'" \<n3fe@repeater.net\>; \<app\_rpt-users@ohnosec.org\>  
> Sent: Friday, July 05, 2013 12:56 PM  
> Subject: Re: [App\_rpt-users] Issue with Hangup after first keying
> 
> > Ok all I'm back to work today and playing with this setup again.
> > 
> > I was able to isolate a much better signal for COR than what I had before.  
> > This now truely goes from 0V-\>5V only when receiving and not when  
> > transmitting. However I'm still having issues.
> > 
> > As soon as asterisk receives a signal it immediately tries to transmit a  
> > signal out. This then effectively pulls the PTT low and my receiver stops  
> > receiving. It is almost like it is in duplex mode but I have in  
> > usbradio.conf
> > 
> > duplex=0 ; Full Duplex
> > 
> > rxondelay=0 ; Uncomment and/or adjust for simplex nodes to  
> > eliminate "Ping Ponging"  
> > &nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;; or "Relay Racing".  
> > &nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;; A positive value here will instruct the usbradio  
> > driver to ignore the  
> > &nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;; COR line for a specified number of 20mSec  
> > intervals following the  
> > &nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;; release of PTT. Use this only on simplex nodes,  
> > and leave commented  
> > &nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;; out for repeaters or other full duplex nodes.  
> > eeprom=1
> > 
> > Just for clarity I'll post my entire usbradio.conf below:
> > 
> > [general]
> > 
> > [usb]
> > 
> > hdwtype=0 ; Leave this set to 0 for USB sound fobs modified  
> > using  
> > &nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;; the instructions from usbfob.pdf. Use a setting of  
> > &nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;; 1 is for Dingotel/Sph interfaces.
> > 
> > rxboost=1 ; 0 = 20db attenuator inserted, 1= 20db attenuator  
> > removed  
> > &nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;; Set to 1 for additonal gain if using a low-level  
> > receiver output
> > 
> > rxctcssrelax=1 ; reduce talkoff from radios w/o CTCSS Tx HPF  
> > &nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;; Do not change this, leave this as a 1
> > 
> > ;txctcssdefault=100.0 ; default tx ctcss freq, any frequency permitted  
> > ;rxctcssfreqs=100.0 ; rx ctcss freqs in floating point. must be in table  
> > ;txctcssfreqs=100.0 ; tx ctcss freqs, any frequency permitted  
> > rxctcssoverride=1 ; Set to 1 or yes to start out in carrier squelch  
> > mode
> > 
> > carrierfrom=usb ; no,usb,usbinvert,dsp,vox  
> > &nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;; no - no carrier detection at all  
> > &nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;; usb - from the COR line on the modified USB sound  
> > fob  
> > &nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;; usbinvert - from the inverted COR line on the  
> > modified USB sound fob  
> > &nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;; dsp - from RX noise using dsp techniques  
> > &nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;; vox - voice activated from RX audio
> > 
> > ctcssfrom=no ; no,usb,dsp  
> > &nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;; no - CTCSS decoding, system will be carrier  
> > squelch  
> > &nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;; usb - CTCSS decoding using input from USB FOB  
> > &nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;; (currently not supported)  
> > &nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;; dsp - CTCSS decoding using RX audio in DSP.  
> > &nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;; rxdemod option must be set to flat for this to  
> > work.
> > 
> > rxdemod=speaker ; input type from radio: no,speaker,flat  
> > &nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;; no - RX audio input not used  
> > &nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;; flat - Use RX audio from discriminator (before  
> > de-emphasis)  
> > &nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;; speaker - use de-emphasized audio
> > 
> > txprelim=no ; Audio processing on left output channel: no,yes  
> > &nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;; no - Audio is not pre-emphasized and limited.  
> > &nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;; Suitable for use on a microphone input  
> > &nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;; yes - Audio is pre-emphasized and limited.  
> > &nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;; Suitable for direct connection to an FM modulator
> > 
> > txlimonly=no ; Audio limiting with no pre-emphasis on output  
> > channel: no,yes  
> > &nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;; no - Audio is not limited.  
> > &nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;; yes - Audio is limited.  
> > &nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;; Suitable for transmitters with no limiting but  
> > with pre-emphasis.
> > 
> > txtoctype=no ; Transmit tone control type: no,phase,notone  
> > &nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;; no - CTCSS tone encoding with no hang time  
> > &nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;; phase - encode CTCSS and reverse phase  
> > &nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;; AKA ("reverse burst") before unkeying TX  
> > &nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;; notone - encode CTCSS and stop sending tone before  
> > unkeying TX  
> > &nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;; AKA ("chicken burst")
> > 
> > txmixa=voice ; Left channel output: no,voice,tone,composite,auxvoice  
> > &nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;; no - Do not output anything  
> > &nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;; voice - output voice only  
> > &nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;; tone - CTCSS tone only  
> > &nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;; composite - voice and tone  
> > &nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;; auxvoice - auxiliary voice output at headphone  
> > level for monitoring
> > 
> > txmixb=no ; Right channel output: no,voice,tone,composite,  
> > auxvoice  
> > &nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;; See txmixa above.
> > 
> > invertptt=0 ; Invert PTT 0 = ground to transmit, 1 = open to  
> > transmit  
> > &nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;; This is the collector lead of the 2n4401 on the  
> > modified  
> > &nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;; usb sound fob.  
> > &nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;; please refer to the howto for the procedure to do  
> > this.
> > 
> > duplex=0 ; Full Duplex
> > 
> > rxondelay=0 ; Uncomment and/or adjust for simplex nodes to  
> > eliminate "Ping Ponging"  
> > &nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;; or "Relay Racing".  
> > &nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;; A positive value here will instruct the usbradio  
> > driver to ignore the  
> > &nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;; COR line for a specified number of 20mSec  
> > intervals following the  
> > &nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;; release of PTT. Use this only on simplex nodes,  
> > and leave commented  
> > &nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;; out for repeaters or other full duplex nodes.  
> > eeprom=1
> > 
> > Any thoughts on why asterisk would be trying to send a signal as soon as it  
> > receives one? After the first time (upon asterisk restart) it receives a  
> > signal it sends a beep followed by a morse code sequence.
> > 
> > Thanks,
> > 
> > Josh
> > 
> > -----Original Message-----  
> > From: Corey Dean [mailto:n3fe@repeater.net]  
> > Sent: Thursday, July 04, 2013 8:48 AM  
> > To: Joshua Hintze; app\_rpt-users@ohnosec.org  
> > Subject: RE: [App\_rpt-users] Issue with Hangup after first keying
> > 
> > Are you running full duplex on a simplex radio?
> > 
> > Corey N3FE  
> > \_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_  
> > From: app\_rpt-users-bounces@ohnosec.org [app\_rpt-users-bounces@ohnosec.org]  
> > On Behalf Of Joshua Hintze [joshh@imsar.com]  
> > Sent: Wednesday, July 03, 2013 3:58 PM  
> > To: app\_rpt-users@ohnosec.org  
> > Subject: [App\_rpt-users] Issue with Hangup after first keying
> > 
> > Hello,
> > 
> > It is my first posting on here. I have ALMOST gotten the ACID installation  
> > working. I'm using the URI interfaced to ACID and to my radio. The asterisk  
> > can properly key the radio and its working just fine with that. I can also  
> > connect to the node with iaxRpt directly with no problem and transmit OUT of  
> > my radio.
> > 
> > However I am having some issues when my radio receives communication in that  
> > as soon as I get my first radio RX, asterisk will then play a tone out of  
> > the URI into the radio over and over again at about a one second interval.  
> > In the asterisk terminal it just keeps repeating:
> > 
> > &nbsp;&nbsp;&nbsp;-- Hungup 'Zap/pseudo-1726358622'  
> > &nbsp;&nbsp;&nbsp;-- Hungup 'Zap/pseudo-1774817359'  
> > &nbsp;&nbsp;&nbsp;-- Hungup 'Zap/pseudo-691532115'  
> > &nbsp;&nbsp;&nbsp;-- Hungup 'Zap/pseudo-81389311'  
> > &nbsp;&nbsp;&nbsp;-- Hungup 'Zap/pseudo-465154784'  
> > &nbsp;&nbsp;-- Hungup 'Zap/pseudo-627058532'  
> > &nbsp;&nbsp;&nbsp;-- Hungup 'Zap/pseudo-1656870264'  
> > &nbsp;&nbsp;&nbsp;-- Hungup 'Zap/pseudo-1671691803'  
> > &nbsp;&nbsp;&nbsp;-- Hungup 'Zap/pseudo-50274194'
> > 
> > forever keeping my radio always keyed.
> > 
> > I have the COR from the radio going into the URI. I do not plan on using  
> > CTCSS and have tried tying it to ground as well as tying it to the COR as  
> > well. My usbradio.conf has the following:
> > 
> > carrierfrom=usb  
> > ctcssfrom=no
> > 
> > I have tried also ctcssfrom=usb as well.
> > 
> > Any help would be appreciated.
> > 
> > Thanks,
> > 
> > Josh
> > 
> > --  
> > This message was scanned and is believed to be clean.  
> > Click here to report this message as  
> > spam.\<[http://simba.repeater.net:8080/cgi-bin/learn-msg.cgi?id=6EF48221A.A93B](http://simba.repeater.net:8080/cgi-bin/learn-msg.cgi?id=6EF48221A.A93B)  
> > \>
> > 
> > \_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_  
> > App\_rpt-users mailing list  
> > App\_rpt-users@ohnosec.org  
> > [ohnosec.org](http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users)

---

<div class="post-metadata">

**Author:** ![Joshh](https://community.allstarlink.org/letter_avatar_proxy/v4/letter/j/8e8cbc/32.png) [@Joshh](https://community.allstarlink.org/u/Joshh)\
**Post date:** [July 5, 2013, 6:06pm UTC](https://community.allstarlink.org/t/issue-with-hangup-after-first-keying/10221/19 "2013-07-05T18:06:43Z")

</div>

Wow that is it!

My rpt.conf did not even have a duplex setting in it so I had no idea that  
it needed to be set. Grrrrr

Seems to be working much better now.

Thanks!

Josh

> **···**
>
> -----Original Message-----  
> From: app\_rpt-users-bounces@ohnosec.org  
> [mailto:app\_rpt-users-bounces@ohnosec.org] On Behalf Of Steve Agee  
> Sent: Friday, July 05, 2013 12:05 PM  
> To: app\_rpt-users@ohnosec.org  
> Subject: Re: [App\_rpt-users] Issue with Hangup after first keying
> 
> For a simplex node be sure that you have the following defined in:
> 
> /etc/asterisk/rpt.conf
> 
> duplex=0 (for no telemetry / messasges)
> 
> or
> 
> duplex=1 (enables telemetry / messages / courtesy tones)
> 
> This is a different setting than the duplex = in your usbradio.conf file
> 
> N5ZUA
> 
> ----- Original Message -----  
> From: "Joshua Hintze" \<joshh@imsar.com\>  
> To: "'Corey Dean'" \<n3fe@repeater.net\>; \<app\_rpt-users@ohnosec.org\>  
> Sent: Friday, July 05, 2013 12:56 PM  
> Subject: Re: [App\_rpt-users] Issue with Hangup after first keying
> 
> > Ok all I'm back to work today and playing with this setup again.
> > 
> > I was able to isolate a much better signal for COR than what I had before.  
> > This now truely goes from 0V-\>5V only when receiving and not when  
> > transmitting. However I'm still having issues.
> > 
> > As soon as asterisk receives a signal it immediately tries to transmit a  
> > signal out. This then effectively pulls the PTT low and my receiver stops  
> > receiving. It is almost like it is in duplex mode but I have in  
> > usbradio.conf
> > 
> > duplex=0 ; Full Duplex
> > 
> > rxondelay=0 ; Uncomment and/or adjust for simplex nodes to  
> > eliminate "Ping Ponging"  
> > &nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;; or "Relay Racing".  
> > &nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;; A positive value here will instruct the usbradio  
> > driver to ignore the  
> > &nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;; COR line for a specified number of 20mSec  
> > intervals following the  
> > &nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;; release of PTT. Use this only on simplex nodes,  
> > and leave commented  
> > &nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;; out for repeaters or other full duplex nodes.  
> > eeprom=1
> > 
> > Just for clarity I'll post my entire usbradio.conf below:
> > 
> > [general]
> > 
> > [usb]
> > 
> > hdwtype=0 ; Leave this set to 0 for USB sound fobs modified  
> > using  
> > &nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;; the instructions from usbfob.pdf. Use a setting  
> > of  
> > &nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;; 1 is for Dingotel/Sph interfaces.
> > 
> > rxboost=1 ; 0 = 20db attenuator inserted, 1= 20db attenuator  
> > removed  
> > &nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;; Set to 1 for additonal gain if using a low-level  
> > receiver output
> > 
> > rxctcssrelax=1 ; reduce talkoff from radios w/o CTCSS Tx HPF  
> > &nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;; Do not change this, leave this as a 1
> > 
> > ;txctcssdefault=100.0 ; default tx ctcss freq, any frequency permitted  
> > ;rxctcssfreqs=100.0 ; rx ctcss freqs in floating point. must be in  
> > table  
> > ;txctcssfreqs=100.0 ; tx ctcss freqs, any frequency permitted  
> > rxctcssoverride=1 ; Set to 1 or yes to start out in carrier squelch  
> > mode
> > 
> > carrierfrom=usb ; no,usb,usbinvert,dsp,vox  
> > &nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;; no - no carrier detection at all  
> > &nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;; usb - from the COR line on the modified USB sound  
> > fob  
> > &nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;; usbinvert - from the inverted COR line on the  
> > modified USB sound fob  
> > &nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;; dsp - from RX noise using dsp techniques  
> > &nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;; vox - voice activated from RX audio
> > 
> > ctcssfrom=no ; no,usb,dsp  
> > &nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;; no - CTCSS decoding, system will be carrier  
> > squelch  
> > &nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;; usb - CTCSS decoding using input from USB FOB  
> > &nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;; (currently not supported)  
> > &nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;; dsp - CTCSS decoding using RX audio in DSP.  
> > &nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;; rxdemod option must be set to flat for this to  
> > work.
> > 
> > rxdemod=speaker ; input type from radio: no,speaker,flat  
> > &nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;; no - RX audio input not used  
> > &nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;; flat - Use RX audio from discriminator (before  
> > de-emphasis)  
> > &nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;; speaker - use de-emphasized audio
> > 
> > txprelim=no ; Audio processing on left output channel: no,yes  
> > &nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;; no - Audio is not pre-emphasized and limited.  
> > &nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;; Suitable for use on a microphone input  
> > &nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;; yes - Audio is pre-emphasized and limited.  
> > &nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;; Suitable for direct connection to an FM modulator
> > 
> > txlimonly=no ; Audio limiting with no pre-emphasis on output  
> > channel: no,yes  
> > &nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;; no - Audio is not limited.  
> > &nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;; yes - Audio is limited.  
> > &nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;; Suitable for transmitters with no limiting but  
> > with pre-emphasis.
> > 
> > txtoctype=no ; Transmit tone control type: no,phase,notone  
> > &nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;; no - CTCSS tone encoding with no hang time  
> > &nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;; phase - encode CTCSS and reverse phase  
> > &nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;; AKA ("reverse burst") before unkeying TX  
> > &nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;; notone - encode CTCSS and stop sending tone  
> > before  
> > unkeying TX  
> > &nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;; AKA ("chicken burst")
> > 
> > txmixa=voice ; Left channel output: no,voice,tone,composite,auxvoice  
> > &nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;; no - Do not output anything  
> > &nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;; voice - output voice only  
> > &nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;; tone - CTCSS tone only  
> > &nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;; composite - voice and tone  
> > &nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;; auxvoice - auxiliary voice output at headphone  
> > level for monitoring
> > 
> > txmixb=no ; Right channel output: no,voice,tone,composite,  
> > auxvoice  
> > &nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;; See txmixa above.
> > 
> > invertptt=0 ; Invert PTT 0 = ground to transmit, 1 = open to  
> > transmit  
> > &nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;; This is the collector lead of the 2n4401 on the  
> > modified  
> > &nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;; usb sound fob.  
> > &nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;; please refer to the howto for the procedure to do  
> > this.
> > 
> > duplex=0 ; Full Duplex
> > 
> > rxondelay=0 ; Uncomment and/or adjust for simplex nodes to  
> > eliminate "Ping Ponging"  
> > &nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;; or "Relay Racing".  
> > &nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;; A positive value here will instruct the usbradio  
> > driver to ignore the  
> > &nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;; COR line for a specified number of 20mSec  
> > intervals following the  
> > &nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;; release of PTT. Use this only on simplex nodes,  
> > and leave commented  
> > &nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;; out for repeaters or other full duplex nodes.  
> > eeprom=1
> > 
> > Any thoughts on why asterisk would be trying to send a signal as soon as  
> > it  
> > receives one? After the first time (upon asterisk restart) it receives a  
> > signal it sends a beep followed by a morse code sequence.
> > 
> > Thanks,
> > 
> > Josh
> > 
> > -----Original Message-----  
> > From: Corey Dean [mailto:n3fe@repeater.net]  
> > Sent: Thursday, July 04, 2013 8:48 AM  
> > To: Joshua Hintze; app\_rpt-users@ohnosec.org  
> > Subject: RE: [App\_rpt-users] Issue with Hangup after first keying
> > 
> > Are you running full duplex on a simplex radio?
> > 
> > Corey N3FE  
> > \_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_  
> > From: app\_rpt-users-bounces@ohnosec.org  
> > [app\_rpt-users-bounces@ohnosec.org]  
> > On Behalf Of Joshua Hintze [joshh@imsar.com]  
> > Sent: Wednesday, July 03, 2013 3:58 PM  
> > To: app\_rpt-users@ohnosec.org  
> > Subject: [App\_rpt-users] Issue with Hangup after first keying
> > 
> > Hello,
> > 
> > It is my first posting on here. I have ALMOST gotten the ACID installation  
> > working. I'm using the URI interfaced to ACID and to my radio. The  
> > asterisk  
> > can properly key the radio and its working just fine with that. I can also  
> > connect to the node with iaxRpt directly with no problem and transmit OUT  
> > of  
> > my radio.
> > 
> > However I am having some issues when my radio receives communication in  
> > that  
> > as soon as I get my first radio RX, asterisk will then play a tone out of  
> > the URI into the radio over and over again at about a one second interval.  
> > In the asterisk terminal it just keeps repeating:
> > 
> > &nbsp;&nbsp;&nbsp;-- Hungup 'Zap/pseudo-1726358622'  
> > &nbsp;&nbsp;&nbsp;-- Hungup 'Zap/pseudo-1774817359'  
> > &nbsp;&nbsp;&nbsp;-- Hungup 'Zap/pseudo-691532115'  
> > &nbsp;&nbsp;&nbsp;-- Hungup 'Zap/pseudo-81389311'  
> > &nbsp;&nbsp;&nbsp;-- Hungup 'Zap/pseudo-465154784'  
> > &nbsp;&nbsp;-- Hungup 'Zap/pseudo-627058532'  
> > &nbsp;&nbsp;&nbsp;-- Hungup 'Zap/pseudo-1656870264'  
> > &nbsp;&nbsp;&nbsp;-- Hungup 'Zap/pseudo-1671691803'  
> > &nbsp;&nbsp;&nbsp;-- Hungup 'Zap/pseudo-50274194'
> > 
> > forever keeping my radio always keyed.
> > 
> > I have the COR from the radio going into the URI. I do not plan on using  
> > CTCSS and have tried tying it to ground as well as tying it to the COR as  
> > well. My usbradio.conf has the following:
> > 
> > carrierfrom=usb  
> > ctcssfrom=no
> > 
> > I have tried also ctcssfrom=usb as well.
> > 
> > Any help would be appreciated.
> > 
> > Thanks,
> > 
> > Josh
> > 
> > --  
> > This message was scanned and is believed to be clean.  
> > Click here to report this message as
> 
> spam.\<[http://simba.repeater.net:8080/cgi-bin/learn-msg.cgi?id=6EF48221A.A93B](http://simba.repeater.net:8080/cgi-bin/learn-msg.cgi?id=6EF48221A.A93B)
> 
> > \>
> > 
> > \_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_  
> > App\_rpt-users mailing list  
> > App\_rpt-users@ohnosec.org  
> > [ohnosec.org](http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users)
> 
> \_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_  
> App\_rpt-users mailing list  
> App\_rpt-users@ohnosec.org  
> [http://ohnosec.org/cgi-bin/mailman/listinfo/app\_rpt-users](http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users)

---

<div class="post-metadata">

**Author:** ![N5zua](https://community.allstarlink.org/letter_avatar_proxy/v4/letter/n/ac91a4/32.png) [@N5zua](https://community.allstarlink.org/u/N5zua)\
**Post date:** [July 5, 2013, 6:16pm UTC](https://community.allstarlink.org/t/issue-with-hangup-after-first-keying/10221/20 "2013-07-05T18:16:32Z")

</div>

Correct. The default does not define that value, and thus it is assumed at full duplex / repeater setting.

Good deal!

N5ZUA

> **···**
>
> ----- Original Message ----- From: "Joshua Hintze" \<joshh@imsar.com\>  
> To: "'Steve Agee'" \<n5zua@earthlink.net\>; \<app\_rpt-users@ohnosec.org\>  
> Sent: Friday, July 05, 2013 1:06 PM  
> Subject: RE: [App\_rpt-users] Issue with Hangup after first keying
> 
> > Wow that is it!
> > 
> > My rpt.conf did not even have a duplex setting in it so I had no idea that  
> > it needed to be set. Grrrrr
> > 
> > Seems to be working much better now.
> > 
> > Thanks!
> > 
> > Josh
> > 
> > -----Original Message-----  
> > From: app\_rpt-users-bounces@ohnosec.org  
> > [mailto:app\_rpt-users-bounces@ohnosec.org] On Behalf Of Steve Agee  
> > Sent: Friday, July 05, 2013 12:05 PM  
> > To: app\_rpt-users@ohnosec.org  
> > Subject: Re: [App\_rpt-users] Issue with Hangup after first keying
> > 
> > For a simplex node be sure that you have the following defined in:
> > 
> > /etc/asterisk/rpt.conf
> > 
> > duplex=0 (for no telemetry / messasges)
> > 
> > or
> > 
> > duplex=1 (enables telemetry / messages / courtesy tones)
> > 
> > This is a different setting than the duplex = in your usbradio.conf file
> > 
> > N5ZUA
> > 
> > ----- Original Message ----- From: "Joshua Hintze" \<joshh@imsar.com\>  
> > To: "'Corey Dean'" \<n3fe@repeater.net\>; \<app\_rpt-users@ohnosec.org\>  
> > Sent: Friday, July 05, 2013 12:56 PM  
> > Subject: Re: [App\_rpt-users] Issue with Hangup after first keying
> > 
> > > Ok all I'm back to work today and playing with this setup again.
> > > 
> > > I was able to isolate a much better signal for COR than what I had before.  
> > > This now truely goes from 0V-\>5V only when receiving and not when  
> > > transmitting. However I'm still having issues.
> > > 
> > > As soon as asterisk receives a signal it immediately tries to transmit a  
> > > signal out. This then effectively pulls the PTT low and my receiver stops  
> > > receiving. It is almost like it is in duplex mode but I have in  
> > > usbradio.conf
> > > 
> > > duplex=0 ; Full Duplex
> > > 
> > > rxondelay=0 ; Uncomment and/or adjust for simplex nodes to  
> > > eliminate "Ping Ponging"  
> > > &nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;; or "Relay Racing".  
> > > &nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;; A positive value here will instruct the usbradio  
> > > driver to ignore the  
> > > &nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;; COR line for a specified number of 20mSec  
> > > intervals following the  
> > > &nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;; release of PTT. Use this only on simplex nodes,  
> > > and leave commented  
> > > &nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;; out for repeaters or other full duplex nodes.  
> > > eeprom=1
> > > 
> > > Just for clarity I'll post my entire usbradio.conf below:
> > > 
> > > [general]
> > > 
> > > [usb]
> > > 
> > > hdwtype=0 ; Leave this set to 0 for USB sound fobs modified  
> > > using  
> > > &nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;; the instructions from usbfob.pdf. Use a setting  
> > > of  
> > > &nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;; 1 is for Dingotel/Sph interfaces.
> > > 
> > > rxboost=1 ; 0 = 20db attenuator inserted, 1= 20db attenuator  
> > > removed  
> > > &nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;; Set to 1 for additonal gain if using a low-level  
> > > receiver output
> > > 
> > > rxctcssrelax=1 ; reduce talkoff from radios w/o CTCSS Tx HPF  
> > > &nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;; Do not change this, leave this as a 1
> > > 
> > > ;txctcssdefault=100.0 ; default tx ctcss freq, any frequency permitted  
> > > ;rxctcssfreqs=100.0 ; rx ctcss freqs in floating point. must be in  
> > > table  
> > > ;txctcssfreqs=100.0 ; tx ctcss freqs, any frequency permitted  
> > > rxctcssoverride=1 ; Set to 1 or yes to start out in carrier squelch  
> > > mode
> > > 
> > > carrierfrom=usb ; no,usb,usbinvert,dsp,vox  
> > > &nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;; no - no carrier detection at all  
> > > &nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;; usb - from the COR line on the modified USB sound  
> > > fob  
> > > &nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;; usbinvert - from the inverted COR line on the  
> > > modified USB sound fob  
> > > &nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;; dsp - from RX noise using dsp techniques  
> > > &nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;; vox - voice activated from RX audio
> > > 
> > > ctcssfrom=no ; no,usb,dsp  
> > > &nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;; no - CTCSS decoding, system will be carrier  
> > > squelch  
> > > &nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;; usb - CTCSS decoding using input from USB FOB  
> > > &nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;; (currently not supported)  
> > > &nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;; dsp - CTCSS decoding using RX audio in DSP.  
> > > &nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;; rxdemod option must be set to flat for this to  
> > > work.
> > > 
> > > rxdemod=speaker ; input type from radio: no,speaker,flat  
> > > &nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;; no - RX audio input not used  
> > > &nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;; flat - Use RX audio from discriminator (before  
> > > de-emphasis)  
> > > &nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;; speaker - use de-emphasized audio
> > > 
> > > txprelim=no ; Audio processing on left output channel: no,yes  
> > > &nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;; no - Audio is not pre-emphasized and limited.  
> > > &nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;; Suitable for use on a microphone input  
> > > &nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;; yes - Audio is pre-emphasized and limited.  
> > > &nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;; Suitable for direct connection to an FM modulator
> > > 
> > > txlimonly=no ; Audio limiting with no pre-emphasis on output  
> > > channel: no,yes  
> > > &nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;; no - Audio is not limited.  
> > > &nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;; yes - Audio is limited.  
> > > &nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;; Suitable for transmitters with no limiting but  
> > > with pre-emphasis.
> > > 
> > > txtoctype=no ; Transmit tone control type: no,phase,notone  
> > > &nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;; no - CTCSS tone encoding with no hang time  
> > > &nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;; phase - encode CTCSS and reverse phase  
> > > &nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;; AKA ("reverse burst") before unkeying TX  
> > > &nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;; notone - encode CTCSS and stop sending tone  
> > > before  
> > > unkeying TX  
> > > &nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;; AKA ("chicken burst")
> > > 
> > > txmixa=voice ; Left channel output: no,voice,tone,composite,auxvoice  
> > > &nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;; no - Do not output anything  
> > > &nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;; voice - output voice only  
> > > &nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;; tone - CTCSS tone only  
> > > &nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;; composite - voice and tone  
> > > &nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;; auxvoice - auxiliary voice output at headphone  
> > > level for monitoring
> > > 
> > > txmixb=no ; Right channel output: no,voice,tone,composite,  
> > > auxvoice  
> > > &nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;; See txmixa above.
> > > 
> > > invertptt=0 ; Invert PTT 0 = ground to transmit, 1 = open to  
> > > transmit  
> > > &nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;; This is the collector lead of the 2n4401 on the  
> > > modified  
> > > &nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;; usb sound fob.  
> > > &nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;; please refer to the howto for the procedure to do  
> > > this.
> > > 
> > > duplex=0 ; Full Duplex
> > > 
> > > rxondelay=0 ; Uncomment and/or adjust for simplex nodes to  
> > > eliminate "Ping Ponging"  
> > > &nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;; or "Relay Racing".  
> > > &nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;; A positive value here will instruct the usbradio  
> > > driver to ignore the  
> > > &nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;; COR line for a specified number of 20mSec  
> > > intervals following the  
> > > &nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;; release of PTT. Use this only on simplex nodes,  
> > > and leave commented  
> > > &nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;; out for repeaters or other full duplex nodes.  
> > > eeprom=1
> > > 
> > > Any thoughts on why asterisk would be trying to send a signal as soon as  
> > > it  
> > > receives one? After the first time (upon asterisk restart) it receives a  
> > > signal it sends a beep followed by a morse code sequence.
> > > 
> > > Thanks,
> > > 
> > > Josh
> > > 
> > > -----Original Message-----  
> > > From: Corey Dean [mailto:n3fe@repeater.net]  
> > > Sent: Thursday, July 04, 2013 8:48 AM  
> > > To: Joshua Hintze; app\_rpt-users@ohnosec.org  
> > > Subject: RE: [App\_rpt-users] Issue with Hangup after first keying
> > > 
> > > Are you running full duplex on a simplex radio?
> > > 
> > > Corey N3FE  
> > > \_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_  
> > > From: app\_rpt-users-bounces@ohnosec.org  
> > > [app\_rpt-users-bounces@ohnosec.org]  
> > > On Behalf Of Joshua Hintze [joshh@imsar.com]  
> > > Sent: Wednesday, July 03, 2013 3:58 PM  
> > > To: app\_rpt-users@ohnosec.org  
> > > Subject: [App\_rpt-users] Issue with Hangup after first keying
> > > 
> > > Hello,
> > > 
> > > It is my first posting on here. I have ALMOST gotten the ACID installation  
> > > working. I'm using the URI interfaced to ACID and to my radio. The  
> > > asterisk  
> > > can properly key the radio and its working just fine with that. I can also  
> > > connect to the node with iaxRpt directly with no problem and transmit OUT  
> > > of  
> > > my radio.
> > > 
> > > However I am having some issues when my radio receives communication in  
> > > that  
> > > as soon as I get my first radio RX, asterisk will then play a tone out of  
> > > the URI into the radio over and over again at about a one second interval.  
> > > In the asterisk terminal it just keeps repeating:
> > > 
> > > &nbsp;&nbsp;&nbsp;-- Hungup 'Zap/pseudo-1726358622'  
> > > &nbsp;&nbsp;&nbsp;-- Hungup 'Zap/pseudo-1774817359'  
> > > &nbsp;&nbsp;&nbsp;-- Hungup 'Zap/pseudo-691532115'  
> > > &nbsp;&nbsp;&nbsp;-- Hungup 'Zap/pseudo-81389311'  
> > > &nbsp;&nbsp;&nbsp;-- Hungup 'Zap/pseudo-465154784'  
> > > &nbsp;&nbsp;-- Hungup 'Zap/pseudo-627058532'  
> > > &nbsp;&nbsp;&nbsp;-- Hungup 'Zap/pseudo-1656870264'  
> > > &nbsp;&nbsp;&nbsp;-- Hungup 'Zap/pseudo-1671691803'  
> > > &nbsp;&nbsp;&nbsp;-- Hungup 'Zap/pseudo-50274194'
> > > 
> > > forever keeping my radio always keyed.
> > > 
> > > I have the COR from the radio going into the URI. I do not plan on using  
> > > CTCSS and have tried tying it to ground as well as tying it to the COR as  
> > > well. My usbradio.conf has the following:
> > > 
> > > carrierfrom=usb  
> > > ctcssfrom=no
> > > 
> > > I have tried also ctcssfrom=usb as well.
> > > 
> > > Any help would be appreciated.
> > > 
> > > Thanks,
> > > 
> > > Josh
> > > 
> > > --  
> > > This message was scanned and is believed to be clean.  
> > > Click here to report this message as
> > 
> > spam.\<[http://simba.repeater.net:8080/cgi-bin/learn-msg.cgi?id=6EF48221A.A93B](http://simba.repeater.net:8080/cgi-bin/learn-msg.cgi?id=6EF48221A.A93B)
> > 
> > > \>
> > > 
> > > \_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_  
> > > App\_rpt-users mailing list  
> > > App\_rpt-users@ohnosec.org  
> > > [ohnosec.org](http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users)
> > 
> > \_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_  
> > App\_rpt-users mailing list  
> > App\_rpt-users@ohnosec.org  
> > [ohnosec.org](http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users)

[Next page](https://community.allstarlink.org/t/issue-with-hangup-after-first-keying/10221.md?page=2)
